Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Dust mask source for small faces?

Posts

Dust mask source for small faces?

#1

Dust mask source for small faces?

Tony - Memphis

>My wife is very petite. 4'10" and 89#. She needs a dust mask. I'n not much bigger, but all my stuff is too big. Any sources on smallish dust masks? I looked at Dust Bee Gone, but they aren't approved by those N*** standards.

Thanks,

tony

Re: Dust mask source for small faces?

#2

Re: Dust mask source for small faces?

Keith Newton, LR, Arkansas------WebKitFormBoundary

>Tony, I don't like the formed ones. Have you tried the ones like the dental profession uses?

I use the ones which have a loop on each side that hooks behind each ear, but they make them that tie behind the head.

I get mine from Harbor freight now. They are flat in the box, and pleated, with a wire to form over the nose.

Re: Dust mask source for small faces?

#3

Re: Dust mask source for small faces?

Jerry Gibbs

>do they blow exhaust breath down so your glasses don't fog? that is a big deal for me. Jerry Gibbs

Re: Dust mask source for small faces?

#4

Re: Dust mask source for small faces? *LINK*

Don in Northern Arizona

>Tony,

I have found the 3M 7500 series to be the most comfortable half face mask. They come in 3 sizes. You would want to get the small one which is the 7501. I use a 7503, large. My wife uses a 7502, medium. The NIOSH P100 dust filters for them are listed separately on the Amazon page. The mask with filters will fit under a face shield nicely which is a benny when turning.

Don


3M 7501 at Amazon

Re: Dust mask source for small faces?

#5

Here's one *LINK*

Phil Joines Krum, Tx

>We get most of our safety stuff from Gemplers. The link is to Moldex � N95 Alternative Fit Respirator w/ Exhale Valve which is suposed to fit smaller faces.


http://www.gemplers.com/product/49843/Moldex-N95-A

Re: Dust mask source for small faces?

#6

Exhalation is expelled downwards doesn't fog specs

Don in Northern Arizona

>

Re: Dust mask source for small faces?

#7

Not a typical dust mask, but... *LINK*

Joe Pack

>Hi Tony.

Because of my beard, I cannot use a typical dust mask. Instead, I use an excellent contraption called a Resp-O-Rator. It is a snorkel type device that is extremely comfortable to wear and use, and it filters to less than 1 micron. (I think the web site says 97% at .3 microns.) I like the fact that when I don't need it for a few minutes, it stays in place, ready to pivot up again in an instant.

They also make a smaller unit, the Junior, that works on the same principal, but I have not used it, so I can't give a first hand review.

The mouthpiece fits between your lips and teeth. It took me maybe twenty minutes to get used to it, but I don't even notice it now. The nose clip in the pics at the links below can be used, but I just learned to not breathe through my nose when I use the Resp-O-Rator...about a 30 second learning curve.

I know your sweetheart doesn't have the beard problem, but I heartily recommend this unit to anybody. No affiliation, just a VERY satisfied user.

You can buy these at Woodcraft, Packard Woodworking and Hartville Tool. The junior can be seen at http://www.hartvilletool.com/product/10997

The regular can be seen at http://www.hartvilletool.com/product/10834

The guy in the picture is James Duxbury, the inventor (and super nice guy...just a woodturner who got tired of his mustache getting in the way of dust masks). The link below is to his main site.


Resp-O-Rator

Re: Dust mask source for small faces?

#8

Thanks!

Tony - Memphis

>

Re: Dust mask source for small faces?

#9

Not as bad.

Keith Newton, LR, Arkansas------WebKitFormBoundary

>I wear glasses too, and these are a lot easier to make a good fit, because the fabric is softer, and the wire can be formed to fit better than the stiff formed ones.