Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Spraying WB Lacquer

Posts

Spraying WB Lacquer

#1

Spraying WB Lacquer

howard

>I have always sprayed NC lacquer, but don't want the lingering smell in my new shop. I am, however, very skeptical that some brands work the same as the solvent based. Would you please let me know about your favorites and how they compare to solvent. I have 2 guns, do you use one for WB and a different one for solvent? What changes in my method should I make to accomodate WB. Appreciate your help, if WB works as well, might as well make the switch.

THanks,

Howard

Re: Spraying WB Lacquer

#2

Re: Spraying WB Lacquer

Fred Davis

>Howard , how did ou vent the "new shop"?

Might be better to install power vent , then go thru the hassle of WB lacquer and not liking the result.

All you will get with WB that you don't get with NC or CAB lacquers is additional sanding step.

IF WB lacquers were truly a viable substitute for NC or CAB, then the others would have be phased out a long time ago.

Since WB lacquers and polys conform to even CA. standards of voc emmissons you get a false sense of being a good citizen while you are down grading your finish.

Like bill says , drive a few mile less and use what your famliar with.

FredD

Re: Spraying WB Lacquer

#3

Re: Spraying WB Lacquer *LINK*

David C. Lykins - Dallas GA - guitardude

>I'm by no means an expert on this subject, but years ago I had built a spray booth in my basement and knew I didn't want the smell or clean up of nitro' lacquer so I opted for a waterbase solution. I wound up purchasing (in the late 90s) a product called "Premium Spray Lacquer" from a company called "Target Coatings". At the time a gallon was about $30, it sprayed very well, and the cool thing was that you could tint it with waterbased stains and tints. Cleanup was also a peice of cake and much less smelly and messy than the Nitro' counterpart.

For a while they had a few issues with the lacquer, don't really remember exactly what it was, but mine has held up quite well considering I didn't know what the heck I was doing. I've also learned that if you use shellac as a filler you'll have no problem spraying the water base product on top of the Shellac.

Check out their web site, they also have a GREAT user's forum, so I'd check that out also.

I stuck a pic' and link to the site below.

Good luck!


img

Target Coatings Ultimate Spray Lacquer

Re: Spraying WB Lacquer

#4

Re: Spraying WB Lacquer

Mark Rakestraw

>I've also used the USL from Target Coatings that David references. Topcoats "burn in" to the previous coats, very fast drying, sands very easily if you get some raised grain after the first coat. The soap and water clean-up is soooooooooooooooo much more plesant than screwing around with solvents that it's worth switching for just that reason.

Mark

Re: Spraying WB Lacquer

#5

Thanks I'll Give it a Try

howard

>

Re: Spraying WB Lacquer

#6

Re: Spraying WB Lacquer

Mark Mandell - Gone Round In Jersey

>Hi Howard,

Few more things you should know about waterbornes and spraying them.

Waterborne finishes are very INtolerant of surface contaminants like oil and the stearating compounds used in most treated sandpapers. If you use stearated paper to sand your piece, or stain (water or oil), you will usually need to seal the wood under a tie coatbefore applying the waterborne. Water-dissolved dye stains will leach into a waterborne coating unless they are sealed first, and oil stains can present some adhesion issues if not fully cured. Best for this (IMHO) is a coat of 100% dewaxed shellac. The shellac must, however be fresh. If you mix your own shellac from flakes, do not use it under a waterborne finish after 90 days unless it's been refrigerated, and never after more than 6 months. Jeff Weiss (Target Coatings' owner) informed me of this problem (applies to other waterbornes as well). Personally, I mix small fresh batches of shellac for each finishing job. Using old and/or thick shellac coats under these new finishes can often lead to "cold checking" where the shellac literally cracks under the waterborne coating. If you use Zinsers' SealCoat (good stuff), check the 'borne-on' date and reject if older than 1 year.

A shellac sealer will also prevent the waterborne from raising the wood grain as was mentioned. You can use a sanding sealer, but make sure it is compatible with the top coat. Whether shellac or other tie/sealer coat, be sure to give the application 24 hours to fully dry and evaporate any primary or tail solvents before you begin to topcoat.

HVLP guns were (mostly) invented to apply waterbornes. Make sure that your gun is set up with the proper cap and needle. While a .8 or 1.0 cap will apply shellac or NC, you may have trouble with a higher solids waterborne. I've put Target's USL down like glass off-the-gun with a 1.2 cap. Remember, however, that you can't "thin" waterbornes like you do solvent finishes lest you mess up the chemistry balance. Target does make an additive, called SA-5, to assist with brush application of their own finishes, but you should plan on using their finish straight from the can (after straining, of course). Any questions on this score can be addressed to Jeff Weiss at Target here in New Jersey or Jeff Jewitt at Homesteadfinishing.com will give you excellent application how-toes.

If you're used to NC lacquer, spraying waterborne is a bit different in that you do NOT "double hit" the coating. I know some who push solvent lacquer with reapplications on short intervals. Do NOT do this with waterbornes. Allow a good two hours between coats or you risk sags and curing issues.

Waterbornes are now my exclusive topcoat, and I have been most pleased with their clarity and performance. Other nice thing is you won't need a very expensive explosion-proof fan to vent your finishing area as you would if using NC lacquer.

mm

Re: Spraying WB Lacquer

#7

Re: Spraying WB Lacquer

howard

>mark-thanks this was very good guidance and I will keep in mind when I try this.

Re: Spraying WB Lacquer

#8

Re: Spraying WB Lacquer

Jerry M. Banks

>I have a love/hate relationship with waterborn finishes. NC lacquer is so pretty and so easy that it is almost worth the effort of working with the poisonous stuff. Way back when, I worked in a small cabinet shop and when we sprayed it looked like the room was foggy, and we were both very happy. Fast forward 15 years and cleaning pant brushes (outside) with thinner almost knocked me out. I got a buzzing in my ears and almost fainted. I know some folks pay for that feeling but I'll go through the extra hassle of waterborns and stay on my feet.