Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

G&G Ebony Pegs Revisited

Posts

G&G Ebony Pegs Revisited

#1

G&G Ebony Pegs Revisited

Jim Dillon

>Faced with having to make 24 ebony pegs for a G&G-style end table, I looked around for a easier method than what has been described in books, mags etc. Looking at my Jet mini-lathe, I thought maybe it could be made to work. Long (well not so long) story short, it works great and I pass this tip (and a pic) on for those thinking about making a G&G-style piece of furniture.

I used a cork sanding block and worked my way through 120, 150, 180, 220, 320, 400, and 1200 grit sandpaper. The sanding process is VERY fast - about 5-10 seconds for each grit. The nice thing I found is that one can actually see the "pillow" forming during the initial 120 grit sanding and easily adjust the depth of the pillow, the shape of the pillow shoulders, and the shape of the pillow itself. I also found that this method gave me better reproducibility, at least in my hands. When done, I cut the peg off with a bench hook and Dozuki saw.

Maybe I am the only one in the world who didn't know about this method, but it was new to me. Hope it helps. Naturally, one needs a lathe. If you don't have one, might be a good excuse to buy one 8-).

Jim


img

Re: G&G Ebony Pegs Revisited

#2

Ellis Walentine

Nifty, Jim

Ellis Walentine

>It looks like that method gives you a lot of control over the shape of the crown on your pegs, and sanding them to 1200 grit must make them really shine. The only thing that bothers me a bit about this method is that the tip of the plug becomes spherical as opposed to crowned in four directions. I'd have to see how that looks in the finished piece. From a distance, of course, the pegs would still read as squares.

Your post got me to thinking about other possibly effective ways to put crowns on a couple dozen pegs at a time. I'm thinking of a board with a groove in the edge the width of the pegs, with a stop at one end and all the pegs standing in the groove, side by side against the stop. You could use a mill file to ease all the edges at once, and then sand them to whatever grit you like with a curved sanding block. Then turn all the pegs 90° and repeat the procedure. I know I've seen other methods, probably right here. I wonder how Tom Stockton handles this in all his G&G pieces. And I don't have Peart's book on Greene & Greene techniques, so I don't know what he suggests either.

It's an intriguing technical problem, well worth discussion. Thanks for kicking it off for us.

Ellis Walentine, Host

Re: G&G Ebony Pegs Revisited

#3

Another way,.. *LINK*

Don in Northern Arizona

>might be to use a lathe mounted sanding disc as discussed in the link below (see Russ Fairfield's contribution). A stand-alone disc sander would be too fast and hard to control, but Russ mounts his home-made one on a variable speed lathe, and I would think this could be quite controllable. Also, you could build an angled stand for the ways with a groove or small dado to insert your peg blank.

Don


Discussion on the spinny side about disc sanders.

Re: G&G Ebony Pegs Revisited

#4

Re: Nifty, Jim

Jim Dillon

>Ellis,

Boy, you have sharp eyes! Yes, you are right. However, I picked a picture that kinda had an exaggerated "shoulder" so folks could see better. And, IIRC, it was on one of my first experimental trys. One can more closely mimic the pillow shape by holding the sandpaper at a shallower angle. Maybe one could hold one of those soft sponge sandpapers perpendicular to the end of the peg to "square-up" the pillow. Or maybe even your file approach to tweak each side while it is chucked in the lathe - then polish right on the lathe. Perhaps using a block of wood for the sandpaper would help. I see lots of experimentation ahead 8-).

Jim

Re: G&G Ebony Pegs Revisited

#5

Re: Another way,..

Jim Dillon

>Don,

Actually, Darrell Peart in his book on G&G style furniture uses a regular sanding disk with a jig to hold the peg rod and then rotates the rod by hand. He then "pillows" the peg end with sandpaper on a sponge. Jim Shaver posted a nice tutorial on this technique a few weeks ago. I tried to mimic Darrell's jig and used a 1 inch vertical belt sander, but couldn't get good shoulder reproducibility - at least in my hands. I actually have a circular sanding disk, but have so much junk piled in front of it that I just didn't want to move 8-(. So, I tried the lathe. Thanks for pointing me to Russ Fairfield's jig - looks neat.

Jim

Re: G&G Ebony Pegs Revisited

#6

Ellis Walentine

Jim's tutorial was the one I was thinking of

Ellis Walentine

>Thanks for jogging my memory. I'd still love to find a quick and dirty way to do these things. Maybe I should go out and build a G&G piece so I have a good reason to.... :-)

Ellis

Re: G&G Ebony Pegs Revisited

#7

Re: Another way,..

Jim Shaver - Oakville, Ont

>:-) Thanks Jim

Take it easy,

Jim