Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Signing your work question

Posts

Signing your work question

#1

Signing your work question

Ken Platt (Granby, CT)

>Folks -

Usually I've "signed" my pieces with a newly minted coin and my initials burnt in with one of those metal doohickeys. On this project, though, I'd like to write a few words. I had figured I'd just use a permanent marker, but failed to consider that my chosen finish of shellac (padded on) will make that run or just vanish. I tried spraying shellac also - thinking I could just spray a small area - but it still makes the permanenet marker run.

Any ideas as to how I could add a few words without getting too complicated? I was really hoping it could be in my handwriting. Thanks -

Ken

Re: Signing your work question

#2

Re: Signing your work question

BILL White

>Sign after you've done the finishing. I have a stamp with my logo.

Bill

Re: Signing your work question

#3

Re: Signing your work question

Scott in Douglassville, PA

>Might wanna try a paint pen. Michael's has 'em...

Re: Signing your work question

#4

Re: Signing your work question

Ken Platt (Granby, CT)

>I was afraid that would fade or get rubbed off over time - although the marks the kids have made on my coffee table seem to be hanging in there pretty well....I may have to go with that though. Thanks -

Ken

Re: Signing your work question

#5

Try India ink...

John in NM

>Water based, might not run due to the alcohol in the shellac. Or perhaps a gel pen - those are supposed to not "wash" if a forger get hold of your check. Gel pen is certainly easier than the India ink, unless you've already got either drafting pens or a fountain pen.

Re: Signing your work question

#6

Dale Lenz

Re: Might try...

Dale Lenz

>sealing over the ink with varnish first or another non-alchol based finish, let dry, then continue with shellac.

Let us know what works

Re: Signing your work question

#7

Re: Signing your work question

Dick Coers

>Kinda elaborate, but you could write your message, scan to the computer, send to a laser engraver, have them burn to wood, inlay the wood. They could also burn on a part before you assemble. You can burn 1/8 deep if wanted. Like I said, elaborate, but forever.

Can you tell I have a laser engraver? I do a few plugs for guys that do carvings. I burn a little graphic symbol for one guy with the date on a 3/4 dia end grain disc. He drills with a forstner bit and inlays the plug. I charge him $5 each since it's on dowel stock.

Re: Signing your work question

#8

Re: Signing your work question

Mike Holden

>These are all good responses, but, how about simple?

Reading about older furniture, such as the Townsend Goddard pieces, I have always been struck by the fact that PENCIL marks and names survive on bare wood quite well.

Yes, I am saving up to have a stamp with my name made, but till then I sign in pencil, knowing I am in good company; and that pencil marks have a multi-century track record.

Mike

Re: Signing your work question

#9

Re: Signing your work question

Tony - Memphis

>Our dog passed when I was almost finished with a small table for our entry hall. I wrote a little message to him on the bottom of a drawer with a Sharpie. No finish over it. So far, so good.

I guess it was a little silly, but it felt right at the moment. Until now, nobody knew it was even there other than me. If the table lasts, it will probably drive some poor soul crazy trying to figure out who the heck Zorba and Tony were and if they were lovers or what!?!

Tony

Re: Signing your work question

#10

Re: Signing your work question

Ken Platt (Granby, CT)

>I was actually considering pencil. Only thing is, it doesn't show up too well on the oak.

There was a line from the TV show West Wing (I don't know if true or not) that NASA had spent some large sum of money inventing a pen to write in zero G. "Know what the Russians did? They used a pencil".

Ken

Re: Signing your work question

#11

Oil based pens, not expensive Prismacolors

Don in Northern Arizona

>Prismacolors run like crazy under shellac or lacquer.

Don

Re: Signing your work question

#12

Steven Antonucci

Archival pen from craft store

steve antonucci

>I use 005 width pens that I get at the craft stores (Michaels, scrapbooking section). They are labeled Micron, and I've used them without them bleeding into raw wood or over shellac/laquer or any other finish. I usually spray the area after signing one last time, and no runs or smudges...

Steve

Re: Signing your work question

#13

Points Well Taken!

George@Colonel's Workshop-Havertown PA

>

Re: Signing your work question

#14

Re: Signing your work question

Ken Platt (Granby, CT)

>Great responses - I'm off to Michael's tomorrow. I'll post whatever ended up working.

Ken

Re: Signing your work question

#15

Powercrafter

Yonak

>If you have and are handy with a Powercrafter you could print a template of your message, stick it on with "supervisor" tape or rubber cement, and carve through the paper. I have used this method with fairly good results.

Re: Signing your work question

#16

Re: Signing your work question

Jim Dillon

>Ken,

Have you thought about using the permanent marker AFTER you have applied the finish and it is good and dry? Haven't a clue how permanent it is, but I have used a "Sharpie" permanent marker fine point over shellac plus varnish and it seems to go on fine with no bleed. And I just got done signing a piece (varnish/oil finish) and then applying a toluene-free wax and there was no bleed. I have used those anti-forgery (Uniball Signo 207) pigment-based pens on luster finished photographic paper and, to my amazement, they worked fine. Costco sells them for about a buck apiece in a 10-pack - much cheaper than Staples etc. But I have no idea how they will work on wood. Let us know what you decide to go with.

Jim

Re: Signing your work question

#17

What I ended up doing...

Ken Platt (Granby, CT)

>Turned out my wife who is into scrapbooking and stamping had a few of those archival-quality Micron brand pens mentioned, so I tried one. Rubbing with alcohol does remove the writing but it doesn't seem to actually dissolve it, and it doesn't bleed. I went to Michael's anyhow, as I wanted a thicker black than my wife had. These pens seem to come with a number designation, like screws, for their thickness. I got a number 08, which is a thickness of 0.5 mm. I wrote my little message for my daughter, and sprayed some shellac over it (I had one of those zinsser spray cans). I figure now I can continue to pad on the layers of shellac without rubbing the actual writing. However, if I hadn't had the spray can, I'd have just padded on the shellac very gently and quickly, and I think it'd have been fine.

Thanks to all for the responses.

Ken