Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Electrical wiring

Posts

Electrical wiring

#1

Electrical wiring

Jack

>Hi everyone, I am building a 23x40 shop with 12� high ceiling. I have been working on it for 2 years now hoping that I can finish this winter. I am currently working on the electrical portion of the project. I am trying to figure out how to run the wiring to the machines that are placed in the middle of the shop. My shop currently has a concrete floor. I have thought that I could install 8-220 outlets near the dust collector and run the wire to each machine along with piping for the dust collection. I am trying to avoid running the wiring along the floor and keep my options open for rearranging and adding machines in the future. Do any of you have some better ideas? Thank you for your help. I will post pictures at a later date

Re: Electrical wiring

#2

JL

Re: Electrical wiring

JL

>I wouldn't go from a box to near your DC and then back to a machine - too much wire and possibly some current drop.

I have my cabinet saw near the center of my shop. I mounted a junction box near where I was going to put the saw and ran wire from the panel over to the junction box. I then ran a flexible drop cord with a strain relief coil from the junction box down. I plug my saw into the cord.

Re: Electrical wiring

#3

Re: Electrical wiring

mdclor

>I had my outlets put into the ceiling over where I located the machines. With a little forethought you should be able to do this without their being in the way when you are up and running. The electrician used twist lock outlets so there is no chance of them falling out. You can also make your cords a little longer than needed to give you some flexibility.

HTH,

Merle

Re: Electrical wiring

#4

Re: Electrical wiring

Howard Norman-Prescott, AZ

>I would put the outlets in the ceiling with a little extra length on the drop cords for extra possible movement of the equipment.

Re: Electrical wiring

#5

Re: Electrical wiring

Fred Davis

>Jack ,

this may be more then your budget allows , but if you do it , your knees and legs and feet will thank you.

My latest and last shop has a six inch thick concrete slab and over it I put down 2x4 sleepers laid flat on 24" centers.

Over this I glued down 241 plywood which is a grade of 1-1/8th inch plywood which has no voids or imperfections on one face and acts as a subfloor and underlayment at the same time.

Over this I glued down 15 7/8ths inch squares of 1/8th thick Tempered Masonite with edges beveled on the router table and painted it with a two part Epoxy floor paint from Porter Paint. Been down ten years with no discernible wear.

This answers your wiring problem for machines in the middle of the floor since you will have between the 2/4's what amounts to a 22" wide wire chase allowing you to have 240V. outlets in the floor at your machine locations.

Machines near a wall should have the wiring running in the wall studs.

My shop's main room with the machines is 36'x43' and only needed the floor outlets at the two table saws in the middle of the room.

The rest of the wiring is convential in the wall Romex.

Hope this helps.

FredD

Re: Electrical wiring

#6

Re: Electrical wiring

Clint Searl, at the base of Haycock Mtn

>I did similar to Fred. 5/4 x 6 PTYP decking, 24 OC as sleepers on the slab. 1" styrofoam between the sleepers. T&G 3/4" 4x8 Advantech decking on top, painted with porch enamel. Ran 240 and 120 wiring between the sleepers to outlets on the floor.

Clint

Re: Electrical wiring

#7

Re: Electrical wiring

Jack Hartley

>Thanks Fred. Did you seal the concrete before you installed the wood flooring or laid down plastic?

Re: Electrical wiring

#8

Re: Electrical wiring

Randy Johnson Connersville IN

>I ran romex to all receptacles on outside walls. I installed (in a 30X30 building)5 dedicated recepatcles. It came in real handy when I needed a 220 I didn't anticipate because all I had to do was change the plug and the wires in the panel.

Receptacles for machines in the middle of the floor were installed after the machines were in place. I ran 1" emt to a 12X12x6 JB on the ceiling. With the layout I have I ran 1/2" emt along side the dc pipe for the tablesaw. That run fed into a 4X4 duplex box mounted near the floor at the end of the tablesaw(where it is very much out of the way)and contained the receptacle for the jointer and a convenience receptacle. A short stick of emt out of this box feeds to the receptacle for the shaper. A second 1/2" emt run next to this one feeds the tablesaw receptacle, located at the left front corner of the saw and mounted about a foot off the floor where it's easy to plug and unplug when needed. The tablesaw receptacle doubles as the planer receptacle.

I have more or less done what you are talking about, that is used the same area as the DC pipe for conduit drops. One difference between your shop and mine is that you have twelve foot ceilings. My runs are supported at the ceiling and at the board all the boxes are mounted on. With a twelve foot ceiling you should have something from floor to ceiling for support.

Re: Electrical wiring

#9

Re: Electrical wiring

del schisler

>i belive wires hanging down from the ceiling would be in the way Over the saw? And any where you go This is Not from the ceiling for me I have a 12X20 shop and have Wall outlets Lot's of them I will never run out of them You can put outlets down low Or what code is in your area is and that will take care of machine's What i did was run the cord's on the floor You can get a yellow piece of rubber at the Electrical store that has a slot in it Where the wire goes It is angled on the long run so that you don't stumble on it Mine has been that way for 15 yrs and no problum Just my 2cent's or less

Re: Electrical wiring

#10

I'm with you Del

Gary Camp, Bend, oregon

>My old work shop had ceiling plugs over the saw and work table. they drove me crazy. I finally pulled the wire out. When we moved the shop to a mew building I got floor plugs. My home shop has cords on the floor and nit's never been a problem.

glc

Re: Electrical wiring

#11

Re: Electrical wiring

Fred Davis

>Yes , I had the concrete crew apply concrete compound as soon as it was dry eough to walk on.

Out here is John Deere country that was a new concept, I got the compound from concrete batch plant in Abilene.

I don't know how widespread this type of construction practice ignorence is , but concrete needs to have a curing compound applied to all flat work right after troweling will accept walking on it.

This prevents the concrete from drying to quickly though the surface ,omittence of this simple task will reveal it's self in shinkage cracks in less then a year.

The curing compond also prevents spalling and dusting of the surface.

FredD

Re: Electrical wiring

#12

Re: Electrical wiring

Fred Davis

>I may have misunderstood your post , but it sounds to me like multiple 240 machines on one circuit.

This of course is a code no-no since each 240v. machine needs to be on a dedicated circuit.

Beyond that receptacles and plugs are not designed to be continually used for a switch, that is what switches are for.

If that were in my shop I would knots on my head from bending over for connection and straghting up in to the saw table. ;-))

FredD

Re: Electrical wiring

#13

Re: Electrical wiring

Randy Johnson Connersville IN

>"What we have here is a basic failure to communicate."

The receptacle for the table saw is almost in the exact center of the shop. When I use the planer, I pull it along side the saw, unplug the saw, and plug the planer in. So, while I am using the same 220 circuit for two machines, I can only use one of them at a time.

Re: Electrical wiring

#14

Re: Electrical wiring

Fred Davis

>This true Randy and I don't really care how you connect the machines , but....... the continual pluging in and unpluging wears the receptable and Nema plug far faster then they were disigned for.

Analogus to turning off a light by screwing it in and out , but I digress.

FredD

Re: Electrical wiring

#15

Are the 220v plugs/receptacles...

Tom Dunlap

>...really that fragile?

I'm not being a smart mouth...I really would think that they are robust enough to be unplugged many thousands??? of times. My scrap bin holds some 220v plugs that look quite sturdy...even better than the 110v ends that I've used on extension cords or power tools for years.

Would there be some sort of sign that the 220v connectors were wearing out that would be different than what we're used to from 110v?

Thanks,

Tom

Re: Electrical wiring

#16

Re: Electrical wiring

Randy Johnson Connersville IN

>The planer isn't used that often. As far as the saw is concerned I can promise you that it gets unplugged quite often. Like every time I change blades, install stack dados, or anything else that might cause a body part to go sailing across the shop if the saw were to come on by accident. Even if I used the really expensive receptacles, which I didn't, the cost of replacement would be minor over the expected life of the plug.

ALL of my handheld powertools get plugged in and unplugged even more than the tablesaw. I've had some of them for decades without any problems to date.

Re: Electrical wiring

#17

Re: Electrical wiring

Fred Davis

>If you retrofit a Magnetic switch to your saw , then worries about it coming on unexpectedly would be a thing of the past.

FredD

Re: Electrical wiring

#18

Re: Are the 220v plugs/receptacles...

Fred Davis

>UL approved switches are typically rated as million cycle work life, hard to say about plugs and receptables, though I have seen people jerk them out, generally at a angle and cause the breaker to trip , sparking , flashing and even wiring the plug wrong , not keeping continuity, not fastening the fixture box securely , using old work boxes on new sheetrock, instead of fastening to the stud or a block and so on.

All of the above is why the NEC exists and is enforced in most areas of the country.

FredD

Re: Electrical wiring

#19

Re: Electrical wiring

James Clark

>Jack,

When I had my old shop I used to have to plug in and out and switch tools around to compansate to make sure the planer and other 220 amp tools had enough amps to properly opperate the tool to their fullest potencial so eight years ago when I built my new shop I spent alot of time drawing up floor plans to best locate the tools and their power supplies. Before I poured the concrete floor I checked with the building/electrical inspectors to be sure I wasn't breaking any codes and in turn be able to pass inspections when I was done. Under the concrete floor is a web of "3 PVC pipes running from the breaker box to each tool. While yes it costs a bit more to do its more than paid for its self whenever I've needed to upgrade to heavier amp wire as I've upgraded to bigger and better tools. As a matter of fact our local building ispector did the same thing when he built his shop after he seen mine. If I did not run the electrical the way I did I'd have rurn the wires in a chase along the ceiling.

Good Luck,

J,Clark