Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Here�s an update on the Wayne Dalton opener...

Posts

Here�s an update on the Wayne Dalton opener...

#1

Here�s an update on the Wayne Dalton opener...

Ralph Turney

>...I just bought and installed.

First off things were going great with only one hitch (no biggie really, I had the wires for the sensors in the wrong places�its fixed now) and had it all installed and had run the program that sets the limits. It all worked perfectly, I was jazzed!!! I ran it through the cycle a couple of times without any issues�and then it happened, I pressed the button to bring the door down and it only hummed, so I waited a few seconds and pressed the button again and all hell broke loose. The door broke loose and came half way down with one side about 2 feet more than the other, rollers started to come out and one corner of the door came loose and swung down. Now, all the while, I�m standing underneath this 500 pound door waiting to get crushed and as luck would have it, it stalled and came to a halt.

I know I said I would only call a repairman over my dead body�well; this was certainly the time for it. I gave it a shot trying to fix it myself and quickly realize that it was the better part of valor was to get expert help. The repair guy showed up a couple of hours later and fixed the door and it�s all working now. It seems that the cable on one side came loose causing the door to causing the door to rack.

I was very impressed with the opener at first, but now I�m not feeling very warm and fuzzy. Every time I use it I�ll be wondering if it�s going to do the same thing and ruin my day, not to mention that now I�m afraid to let my daughter go near it.

I paid 330 dollars for the opener and 150 dollars for the repair of my door for a total of 480 dollars�not what I was expecting. Not only that, but it tweaked my door so bad that I�m not sure it�s safe anymore, so now I have to spring for a new one pretty soon. And I don�t think I�ll go with the Wayne Dalton again, I�ll pop for a jack shaft model or have the installer put in whatever he recommends.

I�m not blaming anyone here for this; I thought it looked like the answer to my dilemma also. It just really sucks; this is costing me a small fortune and lots of precious time.

Vent over.

Ralph

PS, I also jumped into the pool yesterday with my cell phone clipped to my shorts�can you say short?

Re: Here�s an update on the Wayne Dalton opener...

#2

Re: Here�s an update on the Wayne Dalton opener...

Clint Searl, at the base of Haycock Mtn

>Some days you eat the bear, and some days the bear eats you.

Clint

Re: Here�s an update on the Wayne Dalton opener...

#3

Re: Here�s an update on the Wayne Dalton opener...

LAWRENCE MATHESON

>I've installed three Wayne Dalton overhead garage doors and openers without any problems. They've been in service for several years and have operated withoyt incident. In my opinion, they are very good doors.

Re: Here�s an update on the Wayne Dalton opener...

#4

Re: Here�s an update on the Wayne Dalton opener...

Don at Central Illinois

>Funny you should bring this up. I purchased and installed one 5 or 6 years ago and it worked great. A couple of weeks ago, it died. I called Wayne Dalton and they sent me a new head, not charge. Put it up and started working great and then one of the cables broke. Not their fault, just happens occasionally. Purchased a set of cable drums, locally and hope to fix it tonight. They have been great standing behind their product, at least with me. Good luck.

Re: Here�s an update on the Wayne Dalton opener...

#5

Re: Here�s an update on the Wayne Dalton opener...

Ralph Turney

>I'm not saying they aren't great door openers, I just think they may be more sensitive to the door set-up than a regular openers. The repairman seemed like a good guy and the very first thing he did without any advanced knowledge when he saw the door all askew was ask if it was an idrive opener . When the last guy repaired the door, he set the springs kind of loose, just a little hard to open, this guy set the springs on the tighter side making the door a little harder to close. His reason for doing this was to keep the cables on both sides more snug with less tendency to come off the rollers.

I'm still hoping for the best.

Ralph

Re: Here�s an update on the Wayne Dalton opener...

#6

Cables?

Mark Goodall - ATL - tooljunkie

>What cables came off? My garage door has torsion springs (large springs wrapped around the bar that runs along the top of the door over it) and there are no cables involved.

I thought that the iDrive only worked on torsion spring garage doors.

Happy Woodworking!

Re: Here�s an update on the Wayne Dalton opener...

#7

Re: Cables?

Ralph Turney

>"What cables came off?"

Hey Mark,

The torsion springs surround to a 1" tube (that's what the idrive wraps around) that runs the length of the door...at each end of the tube is a 4 or 5 inch pulley that has grooves for an 1/8" cable, that cable is attached to the bottom of the door, if it's a roll up. This is what counter acts the weight of the door and makes it possible for it to be opened by anyone other than Arnold. I think that if you look closer you'll see the cables running up each side of the door.

I used it all day and it's still working!!!

Ralph

"My garage door has torsion springs (large springs wrapped around the bar that runs along the top of the door over it) and there are no cables involved.

I thought that the iDrive only worked on torsion spring garage doors."

Re: Here�s an update on the Wayne Dalton opener...

#8

Oh, the garage door springs.....

Mark Goodall - ATL - tooljunkie

>My mistake. I know what you mean now. I was thinking about cables for the opener, not the door itself. I also got confused because there is one cable that comes out of the opener, runs across the top and then down the side a couple of feet for that manual disconnect handle and thought that was what came off. Either way, I was confused.

Happy Woodworking!

Re: Here�s an update on the Wayne Dalton opener...

#9

Re: Oh, the garage door springs.....

Stuart Hough

>I, too, did the "I installed it just fineand THEN had to call the door man" thing. He told me I had set the tension too loose on one side. That's why the cable did its thing. He set the tension equally, then added 2 increments more tension to help keep the cables taut.

Re: Here�s an update on the Wayne Dalton opener...

#10

Re: Oh, the garage door springs.....

Ralph Turney

>Well, I can't take credit for how the tension was set before I installed the opener, when I first moved in I had the same company that came out yesterday come out and add braces to the door. After he added the braces he adjusted the springs so the door was heavy to open...whether they were equal in tension or not, I have no idea.

Re: Here�s an update on the Wayne Dalton opener...

#11

How is this the "fault" of Wayne Dalton?

Barry Irby

>I don't even have a garage door opener, so I am not married to Wayne Dalton or any other manufacturer. But I was wondering why you seem to hold Wayne Dalton and the i-Drive accountable for the failure of the cable? Apparently the guy that worked on the door set the cable tension. Why did it come loose? The cables on my manual door are spring loaded and if one came loose I would know, if I survived. Was yours coming loose not a noisy scary event? Just seems to me these might be two separate events that are only remotely connected. Did the Dalton Instructions tell you to adjust the cables? I'm just saying a cable could fail at anytime and wondering if you are not assigning blame to Wayne Dalton because of the timing.

Re: Here�s an update on the Wayne Dalton opener...

#12

It's still working...Wayne Dalton opener

Ralph Turney

>It's working like a champ...I still have my fingers crossed though.

Ralph