Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Mission-type stain and finish

Posts

Mission-type stain and finish

#1

Mission-type stain and finish

Chuck Jurvelin

>I am building several pieces of mission/craftsman style furniture and I am looking for suggestions on the best stains and finishes. I have tried several brands, but I am not totally satisfied with the end result. I want to achieve a dark reddish color and an eggshell to flat finish. Any reccomendations?

Re: Mission-type stain and finish

#2

Re: Mission-type stain and finish

Allan D

>I can't find the link to the page that gave me my procedure but I'll tell you what I use:

I first stain the oak with an water mix analine dye. I use Moser's Brown Mahogany color# W13708. You'll have to experiment with dilution to get the shade you want. It will look purplish until the next step though. Sand lightly because the water will raise the grain a bit. Then seal with a waxless shellac sealer - I think it's a 1 lb cut but I'm not sure. That will bring the color back to a more brownish hue. Then a light sanding with 320 grit. Then I use Behlen's Shading and Glazing Stain in Van Dyke Brown, item # 916-759 from Woodworker.com. Follow the directions. You will be wiping most of it off. Then I spray with a semi-gloss lacquer.

Re: Mission-type stain and finish

#3

Re: Mission-type stain and finish

Tony - Memphis

>Jeff Jewitt has a pretty goof recipe for Mission stuff. You might check his website for articles/recipes. Homestead Finishing is the company.

Tony

Re: Mission-type stain and finish

#4

Re: Mission-type stain and finish *LINK*

Steve Schoene

>There is a Badger Pond article written by Jeff Jewitt that gives a very good Mission Oak finishing schedule. I've given the link.


Mission Oak Finish

Re: Mission-type stain and finish

#5

Re: Mission-type stain and finish

Dave Bair, Eaton Rapids, MI

>Bob Lang, with Popular Woodworking, does a lot of A&C furniture and reseach. I personally know he is very helpful; try him at: robert.lang@fwpubs.com

Re: Mission-type stain and finish

#6

Re: Mission-type stain and finish

Jim Dillon

>Chuck,

Here are a couple of recipes, with sources.

1. Sand 120g with ROS;

2. Handsand 150g (no finer);

3. Olympic Interior "Special Walnut" oil-based wood stain - apply with rag. Let sit 15 minutes, wripoe dry;

4. Watco "Dark Walnut" Danish Oil, saturate, 15 min wait, wipe dry;

5. Zinsser's Bulls Eye amber shellac - one coat;

6. Lightly rub with nylon abrasive pad; and

7. Paste wax application.

Source: Robert Lang, Woodworking Magazine, Spring 2007.

1. Aniline dye application (color to taste: light oak, reddish-brown, or dark mission brown);

2. Gilsonite containg pigment stain (McCloskey's maple or walnut, Watco dark or medium walnut);

3. Topcoat with finish (satin or matte sheen) of choice - lacquer, shellac, or varnish;

4. Steel wool 0000 (optional); and

5. Application of a dark-colored wax.

Source: Jeff Jewitt, Fine Woodworking, August 2002 (#157).

Based on some recent experiments with finishes for mahogany, I would try medium-brown TransTint solution dissolved directly in T&T linseed oil, followed by Watco Danish Oil Dark Walnut. This is sort of a variation of Robert Langs' finish for his Celendine Stickley table in a past issue of Popular Woodworking. In that case, he used 2-coats of Watco Dark Walnut Danish oil, followed by 3-coats of linseed oil.

Hope this helps.

Jim

Re: Mission-type stain and finish

#7

Re: Mission-type stain and finish

Chuck Jurvelin

>Thanks to all who responded. I have read many articles in Finewoodworking, Wood Magazine, etc., but I'm always looking for a better or easier solution.Thanks again!

Re: Mission-type stain and finish

#8

Re: Mission-type stain and finish

Jim Dillon

>Chuck,

I just reread your OP, and note you would like a dark reddish-brown color. Here is a suggestion in line with my previous post. Make up two master T&T Danish Oil solutions. One contains reddish-brown TransTint, and another contains medium-brown TransTint (concentration 2 oz TransTint/qt Danish Oil - max). Mix 50:50 of each giving a third solution, and give it a try. You will find, I think, that it gives a rich dark brown with a tinge of red. Having the two master solutions will also allow you to juggle the proportions. I think they also make a dark brown TransTint, but I have no experience with it. The TransTint dye solution does not immediately dissolve in the linseed oil but will overnight - and maybe with a little stirring along the way. I always restir just prior to use. The combination of the linseed oil and dye sure make it easy, even for a finishing challenged person like me, to get a nice uniform color. And the amber coming from the linseed oil gives a really rich color. Good luck.

Jim