Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Making your own tools

Posts

Making your own tools

#1

Making your own tools

john lucas

>I do a lot of woodturning demos and one of them is making your own tools where I teach heat treating and simply bending techniques (not really forging) and some silver soldering.

I have been asked to do a tool making demo for a woodworking club. I'm asking for suggestions on tools that they can make. I do make things like marking knives, some carving tools and scratch awls. I've also made some marking gauges over the years. Haven't tried a hand plane yet. I've made a million jigs over the years. Anyway I thought I'd ask for suggestions on what you would like to see if you attended a meeting like this.

Re: Making your own tools

#2

Re: Making your own tools

Glenn Madsen near San Francisco

>For a hand plane building experience, you can either spend 3 minutes, or three hours. It's hard to do much in between, really. The folk on the hand tool forum here have some stuff to show off.

Hand planes are really the only flatwork tools I've built, and I've only done three or four of those. The beauty of them is that, after the blade sets are acquired, the cost of materials is pretty modest, and mistakes are tossed into the burn barrel. And there are MANY sources of reasonable to excellent blade sets.

However, unless you've built these before, I'd leave them as a passing glance in an otherwise marking tool oriented discussion. Saddle squares, dovetail gauges, angle markers, marking knives, etc., are all more approachable for the first time builder.

JMO...

Re: Making your own tools

#3

Re: Making your own tools

Dick Coers

>Some random thoughts; something about scratch stock and scrapers would be good. Talking about steel sources from saw blades. Hand tool guys like to talk about making froes and bark spuds. Silver soldering band saw blade joints is another subject.

Re: Making your own tools

#4

Re: Making your own tools

Mike Holden

>A dovetail gage, a marking gage - especially one with a sliding wedge to lock it, a depth gage, sliding sticks to check squareness of a carcase, a miter gage for trimming molding, bench hook, shooting board, donkey's ear, miter block (kind of advanced for an hours presentation), winding sticks, auxiliary fences for a table saw (could be a weekend in itself)

these are just off the top of my head,

mike

Re: Making your own tools

#5

Re: Making your own tools

john lucas

>Good thought I have a scratch block that I made to duplicate some old molding. I'll take that. Thanks

Re: Making your own tools

#6

Re: Making your own tools

john lucas

>Thanks I've been turning so long that I've forgotten about all the flatwork things I've made that are in drawers and only occasionally used now. I also have some trammel points that I made, circle cutting jig for the router and a lot more. I'll have to take a tour of my shop drawer by drawer this weekend to see what I come up with.

Re: Making your own tools

#7

Re: Making your own tools

John K Jordan

>I think both flat and round workers would be interested a gauge to set a precise angle on a bench grinder. Mike Darlow has an interesting design in his Woodturning Techniques book. Trammel points are always useful.

JKJ

Re: Making your own tools

#8

Re: Making your own tools

john lucas

>John Thanks for the tip. I've made something similar to Mike Darlow's method and use it constantly. I had not thought about it for flat work but it's perfect for rough grinding chisels and plane blades.

Re: Making your own tools

#9

chisels, plane irons, lathe tools

Bill Tindall, E.TN

>We have made plane irons, chisels and lathe tools. I am currently making a set of paring chisels. A bow saw is on the list. Because one can buy better steel alloys than what commercial tools are typically made from, the tools we make are better than what can be bought. In the case of chisels, they can be fabricated for particular tasks, for example short with steep bevels for dovetailing.

Re: Making your own tools

#10

Re: chisels, plane irons, lathe tools

john lucas

>Bill Thanks for reminding me. I have a bow saw I built also. In fact I want to build another one since I have 2 blades. Mine has turned parts of course.