Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

aquarium stand

Posts

aquarium stand

#1

aquarium stand

Marcel

>I am considering building an aquarium stand,but dont want the boxy 3/4" plywood on end sort of thing. I want to build it so that it resembles an antique dry sink with a drawer in the middle and 1 or 2 doors. I am concerned about the strength of the base with the drawer in the middle. Anybody done anything like this?

Re: aquarium stand

#2

Re: aquarium stand

Brent in Montreal

>Hi Marcel,

Most of the weight from an aquarium sits on the ends. As long as you have good support there and your stand is flat and level there's no problem.

Re: aquarium stand

#3

Re: aquarium stand

John E in SC

>Haven't made anything like you describe, but I used to be pretty big into aquariums (back when I had free time!), and one thing to keep in mind - you will probably want to house your equipment (filters, air pump, etc - depending on what kind of setup you have) in the stand. There will be tubes / hoses running from the stand, out the back, up to the aquarium. If I were going to put in a drawer, I wouldn't make it too deep, so there will be room at the back for all of the stuff. If you were really concerned about the weight (and I would be, particularly if it's a large aquarium), you might consider a "half-depth" drawer, and perhaps some substantial bracing running the length of the cabinet behind the drawer. The sides need to be particularly beefy also.

Good luck.

John

Re: aquarium stand

#4

Re: aquarium stand

Chris Friesen

>I'm not sure the sides actually need to be all that beefy if the cabinet is designed to prevent racking.

Wood is amazingly strong in compression, as long as it is braced so it doesn't bend.

Re: aquarium stand

#5

Point well taken...

John E in SC

>I agree racking is one of the main concerns, and a particular problem with aquarium stands since there usually isn't a full back (to allow hoses, etc. to exit). What I did on the one I built was basically a 2X4 frame to hold the aquarium, then covered that with 3/4" plywood. I'm not sure I would trust the joinery on a plywood box alone to hold that weight. A 55 gal. aquarium can easily be pushing 600 lbs. or so.

Also, forgot to mention, make sure your FLOOR can support that kind of weight. I've heard stories about large aquariums causing floor sag / damage.

Re: aquarium stand

#6

Re: aquarium stand

russastrid

>go to an aquarium store and find a stand about the size you want to build and take a look

Re: aquarium stand

#7

Re: aquarium weight

paul in AZ

>You haven't said how big you want to go.

Most if not all aquaria have a glass under surface that does not touch the stand. They have a narrow rim around the edge that takes all the weight. If you are going -say- 40 gallons or more you will have to plan on making sure that the part of the stand under that rim is sturdy enough. Typically this applies more to the long axis of the tank stand sagging than the ends.

Easy enough to look after as long as the top of the stand doesn't have a long unsupported span.

One gallon of water= almost 9 pounds. Add a bit for rocks etc.

Small 10 or 20 gal tanks are not much of a problem

As mentioned, racking is a consideration but one that is easily prevented.

Re: aquarium stand

#8

Re: aquarium stand

Robert Henderson

>My experience is that you WILL get water on the stand at some point. Don't use MDF, pressboard, or anything else that will degenerate when wet.

That having been said, I agree with russastrid, check out the local stores and see how their stands are constructed. Yours, of course, will be MUCH better. Post a picture when you get it done.

Re: aquarium stand

#9

Re: Aquarium stand - Yes.

Ray Carson - Lawrenceville, NJ

>I made one for a co-worker a few years back. It was made of solid poplar to reduce cost and held a 40 gal. (long type) of tank. Corner posts were 2 x 2 sq. and the upper stretchers were 1 x 4's (exact sizes). Long dimension vertical. The lower strechers were 1 x 2's (long dimension vertical) with 1/4 slats running the short distance (front to back) for a bottom shelf. Each slat had its edges chamfered to make a grooved look between the boards. Under the tank tying the upper stretchers together, running the short distance (front to back) was 3/8" All-thread with the bolts exposed and painted black. This served as a support under the center of the tank and kept the stretchers from blowing outward. There weren't any drawers as I had to keep costs to a minimum. I think my design would be very adaptable to a couple of drawers and easily added even to this day.

The poplar was stained Min-Wax Dark Walnut as requested by my co-worker. Three coats of marine varnish were applied, rubbed, sanded, (you name it) to a semi gloss finish. It now resides in Florida. Humidity and what not aside, the tank stand is still in great shape and is in use by my co-workers ex-wife.

Good luck with your project,

Ray

Re: aquarium stand

#10

Re: aquarium stand

Marcel

>Thanks to all respondents. I drew a few ideas from the thread and will begin construction soon.

Re: aquarium stand

#11

Re: aquarium stand

Joseph Mulherin, Sr

>Marcel, many yrs ago I had the plans I got from Popular Mechanics magazine that had six (6) individual aquarium tanks sitting on a table. Filter system was in the center. Could have salt water in any tank and regular water in another tank...all on the same table.

My son needed a project for the Fair so we made this one and entered it....he got a First place, but the people called a coffee table. Was made out of walnut and plywood for floor. We placed it on wheels for mobility but eventually it sagged and we had to remake the floor. Then I placed a center wheel to take the weight. There were 36 pieces of glass I got cut at the local glass shop and we siliconed everything. Worked very well for a couple yrs.

If you research you might be able to get a copy of the plans from Popular mechanics....about 1974-76 issue if I remember correctly.

I still have the table and probably will put it together again and give it to one of the relatives.