Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Veneer flattening Q

Posts

Veneer flattening Q

#1

Veneer flattening Q

Denis Ch�nard, Orl�ans, Ont.

>To my dismay I found out that the veneer I was planning to use on my project (pink satinwood) was warped and "dry" enough that I could not flatten it without cracking. Now I've done a non-negligible amount of veneering in the past, but these veneers were "well-behaved"...

So I look for a veneer flattening recipe, and this one states "3 parts water, 2 parts yellow glue, 1 part vegetable glycerin, and 1 part denatured alcohol". I have all the ingredients, but this recipe leaves me wondering, will the treated veneer glue to the substrate (solid maple) when there's about 30% glue in the "potion"? I was planning to use yellow glue for the veneering, as I don't have the time to experiment with hide glue (project is on a tight deadline).

This seems like impending doom if I go that route... Am I worrying for nothing?

Any help appreciated...

DC

Re: Veneer flattening Q

#2

Re: Veneer flattening Q *LINK*

Brent in Montreal

>Hi Denis,

I've used that recipe and it worked out well. Lately though, I've been using this stuff. I find it easier to work with.


Veneer Softener

Re: Veneer flattening Q

#3

Re: Veneer flattening Q

Dick Coers

>I would say you are worrying too much. I would caution using the titebond if you are laying up large panels. Titebond will leave a flexible glue line and your veneer shows that it has a lot of stress. If this a large panel, and it might be placed by a furnace duct of south facing window, it may have some seaming trouble in the future. I would use Unibond if I was laying it up.

Re: Veneer flattening Q

#4

Ellis Walentine

The recipe I've used

Ellis Walentine

>The mixture I've used for many years is 1 part glycerine to 8 parts water. I usually add just a little bit of liquid hide glue to act as a size once the veneer is pliable and flat. I spray the veneer, both sides with a fine mist of this mixture, then wait a few minutes for it to soften, then press it between heavy (usually novaply or mdf) cauls, with newsprint both sides of the veneer to absorb the excess moisture. Change the paper daily and you should be ready to veneer in a couple days.

Works for me.

Ellis

Re: Veneer flattening Q

#5

recent successful class experience

Bill Tindall, E.TN

>Over on the hand tool side I related a recent experience, posted about 3 weeks ago. It is under a discussion about hide glue.

You are exactly correct that in spite of what the proponents of hide glue claim, it takes considerable experience to use it successfully, unless you happen to be lucky. A friend was very unlucky and it cost him much time, money and 2 sheets of stupendous veneer. You may enjoy reading about the whole affair.

I recently took a class at Mack Headley and Sons shop (class is under WWOTSV.com) that involved veneering crotch mahogany. I put more credibility in advice I get from a professional shop than what I find elsewhere. We did not pre-flatten the wrinkled crotch veneer. You may contact me off line for details if you wish.

There are a zillion recipes for veneer flattening. They all leave stuff in the veneer that could affect subsequent adhesion to the substrate as well as finishing. Therefore, in practicing a flatening procedure from some source realize that the flattening may only be compatible with the subsequent steps that source uses to yield a final product.

Re: Veneer flattening Q

#7

Ellis Walentine

I'd like to hear more...

Ellis Walentine

>...about if and when veneer needs to be flattened. Personally, I've had lousy luck trying to press veneers that had large bulges or ripples, including some crotch mahogany, but they did fine after flattening.

The biggest trouble I have with bulging or bubbled veneer, besides the fact that it often splits wide open when pressed, is that it is virtually impossible to joint clean, straight edges for taping. My technique for jointing the edges was/is to place the veneers between cauls that are larger than the sheet of veneer and clamp them flat, so the veneer is in the same plane as it will be when laid up. I use the straight edge of the caul setup to either rout or block-plane the edges dead straight. If I do this with warped veneer, it springs back to its warped condition after jointing, making it impossible to tape the seam tightly together. I usually use masking tape for seams like this, because it is springy enough to exert a pulling force on the two pieces of veneer, whereas paper tape exerts a much more passive bond.

So, I'm wondering how Headley deals with such situations. Is he suggesting that no veneer ever needs flattening, or does he just not use veneer that is too blistered or rippled to lay up without it? If the concern is the traces of glycerine left in the pores, what about using plain water instead, maybe with a little hide glue for sizing?

Just curious, Bill. Wanna elaborate?

Ellis

Re: Veneer flattening Q

#8

Re: Veneer flattening Q *LINK*

Thomas S Stockton

>Denis,

I do a fair amount of veneering and have only had to flatten anything twice. The first time was a roaring pain and pretty messy but it worked. A couple of months ago I flattened some walnut burl with a commercial flattner/softner worked great. Instead of heavy boards I used my vacuum press. I found the technique at vacuum pressing systems forum. Follow the link and search the forum you will find this technique as well as some recipes for flattener.

As for glue I use regular titebond or titebond extend works great never had a seam split. Unibond is fine to but make sure you wear a good respirator not a dust mask. The stuff has some nasty things in it that can cause pretty bad health problems from exposure over time.

enclosed is a picture of my walnut burl wash on the line.

Tom


img

http://www.vacupress.com/forum.htm

Re: Veneer flattening Q

#9

Re: I'd like to hear more...

Bill Tindall, E.TN

>1. I did not have to make any veneer joints

2. We slathered white glue on the sheets and taped them to the substrate and then mashed them in the press. My sheets had bulges at least 1 " high and one of the other students has as large bulges with even sharper bends. Both were judged ok for skipping flattening. I suspect the water in the glue softened the veneer. I did not mean to imply they never flattened. We presented out veneer for inspection and it was judged ok to not bother flattening. I suspect they have done veneering hundreds of times and know what will work with out the flattening step.

3. but the caution remains. I would not assume that what is used for flattening will be benign in any finishing schedule.

Re: Veneer flattening Q

#10

Re: Veneer flattening Q

Tony - Memphis

>I'm not sure about the exact proportions, but I used the recipe that Daryl Kleil suggests (Vacupress.com). I've never experienced any adhesion issues. I have used it on mahogany crotch veneer and used Unibond, liquid hide glue, and poly glue.

Tony