Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

is it possible to tint shellac

Posts

is it possible to tint shellac

#1

is it possible to tint shellac

Bruce, a MN Galoot

>for brushing it on? I don't have spray equipment and I don't want to get it. I'm refinishing a pine table that had a perfectly acceptable oil finish and now my LOML wants it to be darker, coming close to the natural finish on a walnut end table.

Transtint dyes in shellac work well, but I can't see any way to brush on that much shellac and get even color across a table that measures 30" X 60". This will go on over the top of a shellac sealer to help control dye absorption.

Any ideas?

Thanks.

Bruce

Re: is it possible to tint shellac

#2

JL

Have you thought of padding it on?

JL

>You can tint shellac. I've used Transtint to tint shellac before - I haven't really tried other stuff, but I've seen it done.

Re: is it possible to tint shellac

#3

Don't brush 'till you roll

Dave Bair, Eaton Rapids, MI

>I've had very good results shellacing large, flat surfaces by quickly applying the shellac with a foam roller and then brushing it out with a synthetic-bristle brush. Use a foam roller that isn't harmed by alcohol (I've had best luck with white foam) and use as wide a brush as you can handle. The foam roller will tend to produce bubbles as your roller unloads and you press harder to spread the finish. The brush eliminates the bubbles and helps level nad even the overlap areas, especially helpful if the shellac is tinted.

Re: is it possible to tint shellac

#4

Yes, BUT

Mark Mandell - Gone Round In Jersey

>You'd be better advised (IMHO) to put most of your colorant in stain rather than the shellac. Since I assume you want to maintain transparency in the finish, too much dye or in too heavy a shellac coating with give you problems in several areas like cracking. You can pad on your shellac with a french polish stroke (start and end off the surface) and do well, but I view toning with tinted shellac as a way to "push" a finish's color a bit rather than make up the primary color. Why not go with a walnut stain over what you have now, sanded in with 320 w/d paper if needed, then seal and tint with a bit of shellac, and finally top coat with a coat or 2 of good waterborne poly like Enduro or Oxford 9000. I think you'll have a much more durable surface this way.

Re: is it possible to tint shellac

#5

Yes, it will be a problem.....

Howard Acheson

>...brushing to padding on highly tinted shellac and getting an even coloring. Keep in mind that whether you use a tinted varnish (AKA the infamous Polyshades) or shellac you will have the same problem. The slightest variation in film thickness will result in differing tones. More coats just exacerbates the problem.

Are you planning to strip off the existing finish or looking for a shortcut but applying the shellac over the existing finish?

I would strongly recommend coloring and clear coating in two steps. You will have much more control and a better shot at having satisfactory finish.

Re: is it possible to tint shellac

#6

Thanks to everyone for your thoughts

Bruce, a MN Galoot

>I had to sand all the finish off to take out some pretty significant scratches, and that took the whole table down to bare wood. Since this was pine, that meant that any attempt to use plain stain would result in pronounced early/latewood absorption problems, so that's why I wanted to use a stain something over a sealer something. Using a sealer makes it possible to have a more even color. Problem is, I don't have and can't afford to get into spray equipment for the limited times I would use it, which is why I asked about hand application techniques. I've done smaller projects by hand and they have gone well, but a larger table becomes pretty problematic.

I like the idea of rolling it out, and will likely give that a try.

Anyway,

thanks again.

Bruce, working nights this week and somewhat incoherent as a result.

Re: is it possible to tint shellac

#7

Ellis Walentine

You're working too hard

Ellis Walentine

>Use a dye stain instead of a pigment stain and you'll get a uniform color. Varnish over it and you're done.

Just a thought.

Ellis