Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Freud dado set always 1/64 off

Posts

Freud dado set always 1/64 off

#1

Freud dado set always 1/64 off

Dan Mitchell

>I have Freud 8" "Pro" dado set. I haven't used the set much yet, just occasionally to plow out a broad area for things like lap joints. I recently cut a series of grooves with the set in a narrow strip of oak, to be used as a gauge set, using every possible blade combination. The set is supposed to cut 1/4" to 13/16" grooves w/o any shims used. Each and every groove is ~1/64" NARROWER than it is supposed to be. Why would this be the case? I ran 2 cuts using each outer blade separately, thinking perhaps one was cutting a bit narrow, accounting for the missing 1/64, but both produce exactly the same width groove. I suppose one may have tips the right WIDTH, but INSET 1/64th. To the eye, this does not appear to be the case. I guess I could just always insert shims to compensate, but that's kind of a PITA. Is this normal? Is it supposed to be to accommodate "dimensional" lumber? Am I missing something here?

TIA

Dan

Re: Freud dado set always 1/64 off

#2

Re: Freud dado set always 1/64 off

Fred Davis

>Dan ,

I suppose it is possibile that Freud had their side grind set a tad to deep.

The good new is that dados for plywood will fit better ;-))

I have the same set and it says right on the case that it will cross plywood splinter free, nver happened with mine.

FredD

Re: Freud dado set always 1/64 off

#3

Re: Freud dado set always 1/64 off

Howard Acheson

>You might want to go onto one of the forums where Charles M hangs out and ask our question. Charles M is the Freud rep here in the US and is very responsive and helpful. If there is a problem with your dado set, he will quickly make it right.

Go to: http://www.forums.woodnet.net/ubbthreads/ubbthreads.php?Cat=

or: http://www.sawmillcreek.org/forumdisplay.php?f=3

or: http://www.woodmagazine.com/dgroups/

Re: Freud dado set always 1/64 off

#4

Re: Freud dado set always 1/64 off

Dan Mitchell

>Thanks for the replies. I have a sawmill creek login (somewhere) I'll try posting there, thanks for the tip!

Dan

Re: Freud dado set always 1/64 off

#5

Re: Freud dado set always 1/64 off

Bill White

>Contact Freud. I think that you'll find them very helpful.

Bill

Re: Freud dado set always 1/64 off

#6

Two things.

Howard Acheson

>If you assemble just the two outside blades and measure across the tips, what is the measurement (it should be 1/4")? Then if you cut a dado with that set up, what is the width of the dado?

Second, let us know what the final outcome is please. Many have that dado and would be interested.

Re: Freud dado set always 1/64 off

#7

Re: Freud dado set always 1/64 off

Charles M

>Dan,

The SD200 Series and DD200 Series Dado Sets are intentionally made to cut slightly under the nominal dimensions. The primary reason for this is that many are used on saws with much less accuracy than your PM2000 and and if they were on size they could cut wider than desired. You can always shim up but you can't shim down.

Charles M

Freud America, Inc.

Re: Freud dado set always 1/64 off

#8

Re: Freud dado set always 1/64 off

Dan Mitchell

>Charles-I saw your reply to this over on Sawmill Creek, thanks for taking the time to post on both sites.

As I replied over there earlier, I feel the term "nominal" means a quantity could vary in either direction (+/-), not just one. It sounds like the cheaper 200 series simply has a looser tolerance. If mine is 1/64 narrow, and this is nominal, by the standard usage of the term, you have to wonder if someone doesn't get one that is wider by a similar degree, which would of course be impossible to address with shims. After all, there's nothing preventing someone with a "sloppier" saw from buying one of the more expensive, apparently higher-tolerance sets.

Dan