Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Sizing replacement drawers/installing slides

Posts

Sizing replacement drawers/installing slides

#1

Sizing replacement drawers/installing slides

Dan Mitchell

>I want to make replacement drawers for some built in bathroom cabinets, using inexpensive drawer slides. The existing drawers do not have slides. No doubt it varies by the specific slide, but I'm a bit confused over how wide to make the drawers to accommodate/fit the slides. For example, one drawer opening is 14" x 8 5/8", with the existing drawer being 19" deep. The drawer fronts overlap the openings. I've never installed such slides before (let alone made drawers ;-) is there a slide which is particularly easy to use? I can imagine a nightmare of the drawer being too wide to fit with the slides in place, or too narrow to engage the slides on both sides, or the slides not lining up on the drawer & the case (too low or not level on one or the other, etc.,) Any beginner suggestions appreciated!

TIA

Dan

Re: Sizing replacement drawers/installing slides

#2

Re: Sizing replacement drawers/installing slides

George Koch

>Dan, my advise would be to pick out the type of slides you want and purchase them first, then they would give you the clearances needed in the package. George

Re: Sizing replacement drawers/installing slides

#3

Re: Sizing replacement drawers/installing slides

Joseph Mulherin, Sr

>Dan, like George says...pick the slide you want to use on the drawers first. Suggestion: I went to HD and looked and purchased Liberty hardware drawer slides. They are for light weight usage. Typically, they are !/2" each thick... so, two slides would be 1". The drawers would be 13" wide, in you case, one side of the slide mounts on the cabinet wall, and the other piece mounts under the drawer.

they mesh and slide very nicely. For heavier duty, determine how much weight each drawer is going to have to handle and select other drawer slides to suit. Another suggestion...make you drawers using 3/8" Birch plywood all around. Facia boards can be attached for decor of the bathroom, and knobs and handles selected also to suit decor.

Re: Sizing replacement drawers/installing slides

#4

Re: Sizing replacement drawers/installing slides

Joseph Mulherin, Sr

>Dan, another suggestion: Go to www.woodmagazine.com and view their video on making drawers using a very simple and satisfactory setup. Drawer slides are shown too.

Re: Sizing replacement drawers/installing slides

#5

JL

Re: Sizing replacement drawers/installing slides

JL

>Of course if you use center slides, you wouldn't have to worry about it :). You would just need enough clearance for glides on both sides.

Re: Sizing replacement drawers/installing slides

#6

Re: Sizing replacement drawers/installing slides *LINK*

Jim Dillon

>Dan,

Agree with the others to get the slide first to see what clearance is needed. Usually, at least on the slides I've used (Accuride, Lee Valley), the clearance is 1/2 inch +/- 1/32. Suggest getting a Woodworkers Hardware catalog as they have schematics of the slides they carry, IIRC. Their web site also has installation instructions in PDF format for their slides. I think they used to carry Accuride slides, but I now see they carry KV slides which I have no experience with. The Blum Tandem slides are more complicated and for sure you need the instructions. Other vendors (McFeely, Lee Valley) likely offer schematics and instructions as well.

Jim


Woodworkers Hardware

Re: Sizing replacement drawers/installing slides

#7

Re: Sizing replacement drawers/installing slides

Dan Mitchell

>Thanks for all the suggestions. I was also emailed off-group & pointed towards a video series on woodmagazine.com which illustrates the whole drawer process quite well. Guess the next step is to go look at slides.

Dan

Re: Sizing replacement drawers/installing slides

#8

Re: Sizing replacement drawers/installing slides

Barry Irby

>Dan, I worked my way through college building cabinets, so It has been a long time, but we like the KV (Knap Voght {sp?}) 1300 slides. They also make full extension rails. Recently I built a night stand for my son and it called for full extension rails. The big box stores had them for about $12. A friend is still in the cabinet business and sent me to his supplier and I got them for about $4.50 People said, "Oh, you can't buy there, they are wholesale only." They were very helpful and happy to take my cash. (It was Diamond Hill, but I don't think they are national.)

Do as the others have said and buy the slides first. Two pieces of advice, work with care. They are serious about that 1" +/- 1/32 and in fact it might be only +1/32" So get the dimensions right. Also, buy rails that are rated heavier than you think. If you think the drawers full of whatever will way fifty pounds, buy 75 or 100lb rails. My experience is that they are not a lot more money and they move much better.

Re: Sizing replacement drawers/installing slides

#9

Re: Sizing replacement drawers/installing slides

Jim Dillon

>Dan,

Sounds like you are well on your way and even have a video to help you. Yes, having the slides at the same height on both sides of the drawer is important. I cut either a piece of plywood to act as a spacer to assure eveness on both sides, or two pieces of plywood to set the slide on front and rear. If putting in several slides in the same cabinet, I cut the pieces of plywood to the longest length, then when the top slide are installed, cut the plywood spacers to the shorter length. Hope this makes sense. Buy good quality slides and, as suggested, perhaps heavier-duty than needed. I like full-extension slides, but that is my own taste. The drawer will slide even more smoothly when you have a load in it.

Jim

Re: Sizing replacement drawers/installing slides

#10

Re: Sizing replacement drawers/installing slides

Joseph Mulherin, Sr

>Hello, Dan, am asking if you have used the videos to make some progress on your cabinets and drawers? If so maybe you could post some pics so the rest of us could see your work.

Re: Sizing replacement drawers/installing slides

#11

Re: Sizing replacement drawers/installing slides

Dan Mitchell

>I did use the videos, very helpful, thanks for asking. So far, I made one large drawer for a router table I'm finishing up, which worked out pretty well. Been meaning to post some pics. Figured I practice on that before tackling the more cosmetically-demanding bathroom cabinets.

Dan

Re: Sizing replacement drawers/installing slides

#12

Re: Sizing replacement drawers/installing slides

Joseph Mulherin, Sr

>Dan, glad to have been a help on your drawer solutions. Good luck in making the rest of your projects. You can find almost anything regarding woodworking videos at the www.woodmagazine.com website too. I also use the www.popularwoodworking.com website. Any place I can get the information I need for making things simpler and easier I will use.