Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Dyeing Epoxy...

Posts

Dyeing Epoxy...

#1

Dyeing Epoxy...

Brian in Sandusky, OH

>I need to do a repair on a pen, and I will be filling a void with epoxy dyed black.

First, I tried just mixing black paint with West System. It turned into a rubbery sludge.

I know that Jeff Jewitt's Transtint dyes will work, because I've used it before, but funds are tight right now, and I have fountain pen ink on-hand

Anyone know if fountain pen ink (specifically Private Reserve brand) will effectively dye epoxy without contaminating it?

Thanks.

Re: Dyeing Epoxy...

#2

Re: Dyeing Epoxy...

Thomas S Stockton

>Brian

I would try it, just mix it up on a piece of scrap and see if it hardens if it does your good to go. I think people use india ink with out problems so pen ink should be fine it doesn't take much so use as little as possible to much of anything will easily cause problems with epoxy. I use to work for someone who used the powders used to stain concrete so if you have a concrete supply place nearby they would probably sell you a lifetimes supply for a couple of bucks. OSH hardware if you have them used to carry small tubes of epoxy dye cheap that is what I use.

Tom

Re: Dyeing Epoxy...

#3

Re: Dyeing Epoxy...

James Fox

>There are companies that sell black epoxy. Do a google search for "black epoxy" and several will turn up in the first 10-15 hits. If you're a pen turner and you're talking about filling a void in a pen, you can put graphite (the kind available in small plastic containers at hardware stores for lubricating locks) in the void (if it's small) and add a bit of CA (super glue) and sand.

If the void is large, you can repeat the process a couple of times or you could mix the graphite with epoxy (haven't tried it, so test first, but see no reason that the graphite should react with the epoxy and prevent it curing properly).

James

Re: Dyeing Epoxy...

#4

Re: Dyeing Epoxy...

john lucas

>Brian some fountain pen inks are water based and they don't mix well. I use shoe dye most of the time. It only takes a few drops to make it sort of black smokey looking. 5 or 10 drops makes a small batch quite black. The only problem I've ever had with it is if I mix too much then it doesn't harden correctly. It does take quite a bit to do that to it however.

Re: Dyeing Epoxy...

#5

Dale Lenz

Re: Make your own dye

Dale Lenz

>Take some fine sanding dust from oak, walnut or cherry add some iron filing and water, mix. The mix will turn black in front of your eyes. Let mix dry, or force dry it. Use a maganet to remove iron filing when dry. Just a pinch of powder to 5 min. epoxy has worked for me for some 15 years now.

Re: Dyeing Epoxy...

#6

Try Laser Jet Toner

Chad Pearson

>I periodically take a small aspirin bottle to work and harvest some of the toner from old laser jet cartridges. A little bit goes a looong way.

Re: Dyeing Epoxy...

#7

Re: Dyeing Epoxy...

R Payne

>I have ground up natural charcoal and added to epoxy to get a black with good results. The finer the dust the better the results.

ron

Re: Dyeing Epoxy...

#8

Lots of good ideas here...

John in New Mexico

>I like the charcoal and Dale's dye recipe, both use stuff you'll probably have around. Toner is an old standby if you ever manage to use up a cartridge (I can't remember when I last bought one - old HP laser never seems to run out!). Rubbing a pencil on sandpaper to get the graphite dust is another one if you don't have charcoal handy. You could try a little tube of graphite for locks available at just about any hardware store. Stuff we used for tons of mesquite work when I lived in Tucson was a "universal" colorant, available from a paint store or maybe even the borg. Trouble is in the two years I worked there, we bought one bottle (16 oz) for a shop with 5 full time builders. Maybe I should start re-bottling it and selling in on ebay! Couple drops does it, almost sounds to me like you used too much ink. That universal stuff had a glycol base as I remember, and was supposed to work in almost anything (yeah, right, advertising). If the ink doesn't mix well, try mixing it with a little anti-freeze and see what happens.

Re: Dyeing Epoxy...

#9

Update...

Brian in Sandusky, OH

>The fountain pen ink did not work, either.

I was forgetting that it's water-based.

So I ordered the TransTint, just like I should have in the first place!

bg