Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

catching small cutoff pieces at mitersaw?

Posts

catching small cutoff pieces at mitersaw?

#1

catching small cutoff pieces at mitersaw?

Ken Platt (Granby, CT)

>Folks -

I need to cut a bunch of short pieces (under 1 inch) off the end of a 1/4" square piece. I'd prefer to use the mitersaw, but of course when you cut off a tiny piece it goes flying - in my case usually right into the mouth of the dust collection tube, even if the dc isn't on.

Anyhow - looking for tips on how to prevent this and catch the offcuts. I vaguely remember reading some such over the years but can't pull them out of the recesses of memory.

Thanks -

Ken

Re: catching small cutoff pieces at mitersaw?

#2

Re: catching small cutoff pieces at mitersaw?

Tom Dunlap

>I saw a shop tip about this...

setup the shop vac tube right at the blade. It'll pull the piece and the dust into the vac. Then you'll have to sift them out which shouldn't be too hard...as long as you start with an empty vac ;)

Re: catching small cutoff pieces at mitersaw?

#3

Re: catching small cutoff pieces at mitersaw?

Curly Smith

>Attach a piece of screen or wire mesh to the end of the dust collector fitting with a band clamp. The dust will pass through and you can pluck the piece off at your convenience.

Re: catching small cutoff pieces at mitersaw?

#4

Jason Roehl in Lafayette, IN

Simple.

Jason Roehl in Lafayette, IN

>Use a sacrificial table and fence. When you make your cut, cut through then release the trigger and let the saw come to a stop before you let the blade back up. The piece will stay put.

Better to prevent things from flying than trying to catch them when they do...

Jason

Re: catching small cutoff pieces at mitersaw?

#5

Re: catching small cutoff pieces at mitersaw?

wilbur

>Your stock is only 1/4" square? Why not use a handsaw?

Re: catching small cutoff pieces at mitersaw?

#6

'Cause I'm really bad at them....

Ken Platt (Granby, CT)

>I use handsaws a lot, but you know, no matter how many times I read how to cut in a straight line, and try, it just never works out. In this case, it's multiple cuts off of that 1/4" square piece, so I'd have to go to the mitersaw after every handcut to square up the end for the next piece.

Call me handsaw-challenged.

Ken

Re: catching small cutoff pieces at mitersaw?

#7

Re: 'Cause I'm really bad at them....

wilbur

>This may be a bit far for you to drive, but if you want to come from CT to central NJ, I'll be happy to show you how to saw straight. For the type of cut you're describing, a hand saw would be just as fast and a lot safer than a miter saw.

One other thing to consider is to get one of those plastic miter boxes at the Borg. That will help you to saw straight.

Re: catching small cutoff pieces at mitersaw?

#8

Re: catching small cutoff pieces at mitersaw?

Jim Dillon

>Ken,

Frankly, I've had more kick-back and small pieces flying everywhere with my SCMS saw than the TS where I now use a sled to cut almost everything - including small pieces. But when using my miter saw, I do the same as Jason recommended and use a sacrificial fence. I guess it acts like a TS insert. Right now I have a badly beat-up 1x4 on its flat side that I just move when the slot gets too wide. On the TS sled, I just use a handheld piece of wood to hold down the cutoff - and watch where my fingers are.

Jim

Re: catching small cutoff pieces at mitersaw?

#9

Re: catching small cutoff pieces at mitersaw?

Bob Lemon Sacramento Ca.

>Ken, If you post on the turning forum you should get several answers to your questions and possibly pictures of the set-ups.

Re: catching small cutoff pieces at mitersaw?

#10

Vac works, fence less well..

Ken Platt (Granby, CT)

>Folks -

Thanks for the replies. I tried a ZC fence, and the little piece still flew off about 1/2 the time.I was going to figure out how to make and attach a scarificial table, but tried the shop vac approach first, and rather to my surprise, that worked fine. I was surprised because it just seemed unlikely that it'd catch the little pieces, which seemed to want to fly straight back, and the shop vac of course had to be off to the side, couple inches away. But yet, every time, the little cutoff is sitting right there on the mesh covering the vac hose. Way cool.

Wilbur, thanks for the offer. Getting better with hand tools generally is one of my goals, but sometimes ya gotta just get the project out the door. One of these days...

Bob, thanks. It occurred to me after posting that this problem must have been solved by those who turn segmented work. Major "doh!" moment for me.

Ken