Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Heating idea

Posts

Heating idea

#1

Heating idea

Mitch from Canada

>Hi everyone,

I built a new garage 2 years ago and unfortunately to wood "bug" bit me AFTER I built it. At least I have 10' 2x6 walls though.

Just looking at heating it...read about the Radient overhead heaters, forced air etc... I had read in a Shop Ideas magazine from FWW about a guy who installed an insulated sub floor over his concrete slab with 2 x 4s as joices and styrofoam sheets between them. Plywood on top. My (one day soon hopefully) wood shop is in an area 18' by 31' that I share with two vehicles. So my actual space with cars inside is about 18' x maybe 14'. Anyway, I was just tossing the idea around of making a subfloor with in floor pipes running between the joices. Heat of course would be supplied by a Water heater in the shop (Gas or Electric)... Now I don't forsee being able to do this in the area where the vehicles sit due to the wieght, but could I run additional water lines along the walls beside the vehicles like a baseboard, to help heat that section of the garage?

Now, the way I see it, the advantage is in floor heat in the main area where I would work with no air movement. Disadvantages could be the 2 inch difference in hieght from the cement pad under the vehicles to the top of the sub floor.

Anyway, it was just something I was wondering about. Any opinions about what you guys use would be helpful. I'm in Saskatoon,Saskatchewan, Canada. Chilly winters etc...

Any help is appreciated.

Thanks.

Mitch

Re: Heating idea

#2

JL

Re: Heating idea

JL

>I don't know if you would get enough radiated heat just running pipes in the garage section. There are baseboard radiators out there that you can use that heat quite effectively - you might consider those (see url for an example (http://www.slantfin.com/documents/233.pdf))

I don't think 2" difference in height means much. You can easily make a sloped transition between the garage and the shop area. You will have a nice resilient floor system that will be easier on the feet.

If you have an affordable hot water source (gas, electric, wood-fired), it sounds like a great idea. I would consider getting a hot water system designed for heating rather that a hot water heater.

Dust control and some sort of curtaining between the spaces should also be looked into.

My $0.02.

Re: Heating idea

#3

Sleepers

Mark Goodall - ATL - tooljunkie

>In the houses I lived in and owned in Canada, we finished the basement by laying tar paper over the concrete then 2x4 sleepers (on their side) and then plywood. Think we may have also used a plastic vapor barrier somewhere in all that but can't remember for sure.

I remember experts telling us not to put anything underneath (like styrofoam or insulation) because you need good air movement underneath to prevent mold, etc.

Happy Woodworking.

Re: Heating idea

#4

Re: Heating idea

Fred Davis

>Mitch.

don't sweat the vehicle weight, keep the floor one height and here's one way that has be used many times.

Lay the two by fours flat , on 16" centers, use the plastic mats with integral piping that is used for installation between existing floor joists.

Have a plumber do this and he can calculate the number of zones for the manifold that controls the hot water flow.

Then glue and nail down 1 1/8th inch 4'by 8' plywood panels with 2 for 1 grade one face. Then paint it with a good grade of floor paint.

The 2 for 1 grade may not be familiar to you , but it is intended for use under sheet flooring like Linoleum, therefore has no imperfections like knot holes in the face veneer.

It is equivalent to 3/4" subflooring with 3/8" underlayment in thickness , but because it is one piece it makes a very strong flooring material for shops.

FredD

Re: Heating idea

#5

Re: Heating idea

Mitch from Canada

>Thanks for the responses.

Still mulling things over.

Mitch