Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Wacky idea for a crosscut sled

Posts

Wacky idea for a crosscut sled

#1

Wacky idea for a crosscut sled

wilbur

>I probably shouldn't even be bringing this up, since I don't have a table saw, but I was reading up on bench dogs, and how the faces of a bench dog are angled towards the board by 2 degrees or so, to help hold the board in place. Then I was reading about kickback on a table saw.

Then it occurred to me: why wouldn't you put a slight angle on the face of a crosscut sled so that it's tilted towards the blade? That way, the angle would tend to hold the board down against the force of the blade, and might reduce the possibility of a kickback.

I don't have a similar brilliant idea for rip cuts, other than to use a bandsaw instead. :@)

If I had a table saw, I'd make one of these myself, and then send the tip in to one of the magazines so I could get my $50 gift certificate. :@) But I thought I'd put it out here for the WC brain trust (in other words, people who actually know what they are doing) to weigh in.

Re: Wacky idea for a crosscut sled

#2

Dale Lenz

Re: Item item off the top of me head...

Dale Lenz

>is I have used my cross-cut sled while making box joints, board(s) held vertical, up against the fence. By cutting with the boards vertical would put an angle-cut inside the joint.

Just one reason I would not put an angle on the sled fence. Nice safety thought though. I'm still waiting on my billion dollar idea, : ' >.

Re: Wacky idea for a crosscut sled

#3

Dale Lenz

Re: Must be thinking/typing double today, : ' >

Dale Lenz

>

Re: Wacky idea for a crosscut sled

#4

Re: Wacky idea for a crosscut sled

Keith Newton, LR, Arkansas------WebKitFormBoundary

>I was not aware of a problem with the sled that needed this fix.

Re: Wacky idea for a crosscut sled

#5

Re: Wacky idea for a crosscut sled

Bill Howatt

>Kickback isn't much of problem for crosscuts, primarily ripping. Where I have had trouble with crosscut kickback has been small cutoffs occassionally being fired back after they contact the blade. I don't think your solution will do much for that.

Bill

Re: Wacky idea for a crosscut sled

#6

Re: Wacky idea for a crosscut sled

john lucas

>When I owned my shopsmith the table flexed and you had to shift the rip fence slightly outboard to get a clean cut.

When I got my powermatic saw I was very careful to buy a good fence and align it perfectly with the saw blade. I have never had a problem with kickback except 2 instances. When ripping reaction wood it can flex and try to kickback. The riving knife and raising the blade reduce this to maneagable pressures that you can overcome with a push stick.

The other time I got a kick back was when ripping a bunch of 3" square blocks. I always use a board on the rip fence when using miter gauge to give clearance for the wood. However when you use a 3/4" board and the 3" block rotates on the table the diagonal is larger than 3 3/4. It caught the blade and hit me in the chest. You can't believe how hard a 3x3x3/4" piece of pine can hit you. I now use a 6" block clamped to my rip fence when doing cutoffs. This gives plenty of clearance.

I rip a lot of wood for segmented vessels using a sliding miter table. I have never had a problem with kickback on that. I made my table so it rides in both miter slots. This keeps it perfectly square which I believe is one of the secrets of not getting kickback.

Re: Wacky idea for a crosscut sled

#7

Re: Wacky idea for a crosscut sled

Larry Marker

>If you are using a half sled (one that doesn't extend beyond one side of the blade, your tilted fence won't help with the cut-off which will not be supported by the sled and its fence. If you are using a full width sled that extends on both sides of the blade, the object beign cut is fully supported on both sides by the sled and kickback is rarely a problem.

Larry