Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

natural maple color

Posts

natural maple color

#1

natural maple color

Erick Singleman

>Hello folks, I am building a tiger maple trestle table for my kitchen. I have four boards that I am planing to edge glue together. Two of th eboards came from the same longer board, and the other two came from another single board. You can probably guess where I am going. Two of my boards are slightly pink looking compared to the other two.

I want to finish the table with a water clear poly from Oxford to keep the natural color. the breadboard ends and a small one inch trim of cherry will surround the maple.

Any ideas? I ordered some pink water soluble dyes to see if I could match the colors on some spare pieces of the lighter boards.

Re: natural maple color

#2

Re: natural maple color

George@Colonel's Workshop-Havertown PA

>Hello Erick,

I had a similar condition when I built my wife's cedar chest. (Shop Shot 746). I tried two part wood bleach on the two slabs which were a bit darker, and while it helped some, it was not a total cure. I glued it up and finished it. The slight difference is still discernable, but my wife likes it and so it can't ever be changed. I judicious shot of toner would probably even it all out.

George

Re: natural maple color

#3

No pink!

Bill Tindall, E.TN

>No "natural" lumber color is stable. Freshly planed there will often be subtle hues which fade and/ or darken with time in the case of some woods and lighten in the case of others. Put the boards in the bright sun for a few hours. I suspect you will find that neither is the color it was and that the pick is gone. Over time the wood will turn tan, or yellow if your finish yellows any. If you want the maple to assume some color then dye it that color.

Re: natural maple color

#4

Re: natural maple color

Clint Searl, at the base of Haycock Mtn

>One of the pleasures of wood is its natural appearance, so why strive for same-o same-o? Go for a foldout book match and let the wood dance in its natural glory, however pink or otherwise. (Apologies to Thoreau}

Clint

Re: natural maple color

#5

Re: natural maple color

Dick Coers

>I would be tempted to put two of the same color in the middle and one of each on the outside of the those. It wouldn't look half and half. Any color you put on curly maple will really bite into the curl and not so much in the regular grain.

Re: natural maple color

#6

Re: natural maple color

Erick Singleman

>Thanks for the advise. I think I'll put the two pink ones in the middle, and the other s outside as suggested. Then afterglueing and sanding the surface, I'll try setting it out in the sun. i'll be sure to rotate the top so it doesn't dry our more on one side and cause bowing.

I am still going to experiment witht he pink dye in case the pink does not fad away. I'l be sure to seal the wood first so the curl does not preferentially absorb the dye.

Thanks all.

Re: natural maple color

#7

Re: Pink Experiment

Mark Mandell - Gone Round In Jersey

>While your pink may indeed tan up with a bit of UV, if it doesn't you'll be more likely to succeed with a colorant if you go with a toning dye in your finish routine rather than trying to stain the wood to match.

You can easily tone by adding a few drops of Transtint dye to a smaller quantity of your Oxford or other sealer coat and apply that only to the "nonpink" sections. That way you'll avoid the blotching issue, and you can maintain very fine control. I regularly use dewaxed clear/pale shellac and one of several Transtints to blend different parts of cherry items. I normally use a small HVLP spray gun to do this with the material knob dialed way back to give a very thin application on a wide fan.

In your case, 1-2 drops of Bordeaux Transtint in 4oz. of sealer may be all you need. On your scrap, try it as a light first application as well as a second application over a clear first coat. Allow it to dry for several hours before comparing the results.

Hope this helps.

Re: natural maple color

#8

Re: Pink Experiment

Erick Singleman

>Thanks Mark,

I will try the dying on scrap pieces, but if not sucessful, I'll live with the natural colors. BTW, I am looking forward to using the Oxford super clear Poly. Other water based polys I have used have had a haze with more than 2 coats. This stuff is supposed to be much more clear, so they say. I will post my findings here.

Re: natural maple color

#9

Re: Oxford Waterbornes

Mark Mandell - Gone Round In Jersey

>If you've been using Big Box consumer grade finishes, you're going to be amazed. Don't forget to strain it before application. Lumps, etc. are rare but can occur. Are you using a sealer?

Re: natural maple color

#10

Re: Oxford Waterbornes

Erick Singleman

>I was planning on thinning it down for use as a sealer. Unless you know of a water clear sealer?

Re: natural maple color

#11

Don't *LINK*

Mark Mandell - Gone Round In Jersey

>Thin it. This is not a solvent finish like shellac or lacquer that spreads the resin molecules out. Target's site (link) specifically states not to do so.

If you want a thin sealer, I strongly suggest a light coat of freshly mixed dewaxed "ultra pale" shellac. You can apply it in a 1/2 pound cut, let dry to stiffen fibers, sand off lightly and reapply without much effect on the color of the wood. Zinsser's SealCoat can be used as well if it is fresh (less than 1 year from "birth") and you thin it down from its 2-pound cut. There is also the Oxford Ultraseal WB sanding sealer, but I have no experience with it.

Contact Jeff Jewitt at Homesteadfinishing.com, or Jeff Weiss at Target Coatings in New Jersey for information.


Target Manual

Re: natural maple color

#12

Re: Thanks Mark

Erick Singleman

>I didn't realize that. I also didn't realize there was an ultra pale Shellac. Thanks for pointing me in the right direction. I just ordered some from homestead.