Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Chair caning - pricing question

Posts

Chair caning - pricing question

#1

JL

Chair caning - pricing question

JL

>I've been asked to "restore" an old chair. It is a nice simple chair with pressed oak decorations. I figure on cleaning it, replacing the screws with new ones and putting a couple of coats of oil on it. I know how much to charge for that.

It needs new cane though. I can get the caning supplies (and tools) for under $20. I have never caned before and I have no idea how long it will take (several hours for sure). If I'm to bid on the project, I want to have some reasonable numbers. It will be a learning experience, so I don't want to charge full shop rate.

TIA

Re: Chair caning - pricing question

#2

Re: Chair caning - pricing question

Jim Hoeller

>I have replaced the cane in several chairs using woven cane fabic and a spline. The challenge in each was cleaning the grove in the chair. If the cane to be replaced is original, the task is fairly easy. Buy an inexpensive 1/4" wood chisel and grind it down to just under the width of the groove. Use it to remove any residue. If the cane has been previously replaced you may find a lot of dried glue in the groove and it can take quite some time to remove without damaging the wood. I have not been lucky enough to find one that used hide glue which can be removed with a hair dryer.

When installing the new cane, do not put glue in the groove; install the cane and then put glue on it to bind the spline.

Re: Chair caning - pricing question

#3

JL

No spline, all weaving.

JL

>

Re: Chair caning - pricing question

#4

You got Yourself A Jon, JL

George@Colonel's Workshop-Havertown PA

>Good Afternoon JL,

Some folks figured a buck or more a hole when I did it. I generally quoted between $200~$250 per seat. I charged almost that much additional for a back, especially if it was a curved back. I didn't like the work, so charged more than others. It ain't fast or cheap. Tough on my eyes, so I gave it up to do sheet cane exclusively. My last chair was one in which I plugged the cane holes, anbd routed a continuous slot for the spline, then finished with sheet cane. I will say that I admire greatly the people who are successful in hand caning. Also, there is a charm present in a hand-caned chair/back which doesn't exist ina sheet caned counterpart. Maybe Don Henthorn will chime in. He is a Master of the Art.

George

Re: Chair caning - pricing question

#5

Re: Chair caning - pricing question *LINK*

Bob Entwisle in NJ

>Hi JL, funny you should mention caning, I'm redoing a seat I've been promising my wife I'd do for the last 15+ years or more. If I was going to charge someone for this I'd say between 1.50 and 2.00 per hole would be about right.

Attached is a link I found with some pricing.

Bob (in_NJ)


http://www.chaircaningandsupplies.com/index_files/page0004.html

Re: Chair caning - pricing question

#6

JL

And with over 100 holes....

JL

>That's a bit of pocket change. Hmmm - I'll present the estimate. I don't think she'll go for it though. Because that would be in addition to the $50-100 for refinishing the chair. So the total coast for her $10 flea market chair would end up being over $250.

Re: Chair caning - pricing question

#7

Then The Alternative Is To Use Sheet Cane..

George@Colonel's Workshop-Havertown PA

>Good Afternoon JL,

You shouls be able to route a groove without too much trouble, especially if you can dismount the seat. I've plugged the holes first before making the groove for the spline. Sheet caning will reduce the price even though you must devote time to plug holes and route the groove.

George