Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Under Cabinet Microwave/Cabinet depth

Posts

Under Cabinet Microwave/Cabinet depth

#1

Under Cabinet Microwave/Cabinet depth

Theresa K

>Any owners of the Under Cabinet Microwaves out there?

I'm cutting out my cabinet sides from plywood now and bought an Under Cabinet Microwave. I'm making my Upper Cabinets 14" deep. The Microwave depth is 15 1/32".

I've never paid attention to how they were mounted when out window shopping. But normally cabinet displays are 12" depths.

Does the UTCMicrowave protrude under 12" cabinets 3 inches and look ok? Should I bump out the cabinet over the UTCMicrowave to the same depth as the Microwave? It will be the only cabinet that will be at that depth, if I bump it out to fit. Or is there an angled filler between cabinet bottom & Microwave? I suppose I could make the bottom faceframe rails deeper and trim out the bottom to meet the UTCMicrowave.

Thanks in advance for any help.

Theresa

Re: Under Cabinet Microwave/Cabinet depth

#2

Re: Under Cabinet Microwave/Cabinet depth

Eddie Pacheco: San Jose, Ca,

>We have a GE "Profile" under cabinet unit and the door of the microwave is flush with the door fronts of the cabinet. The cabinet is 12" deep and the MW is about 13" deep overall. Door front/face to back of unit.

We have a 12" dp. cab. about a 3/16" rubber bumper on cab. doors and 3/4" thick door stock. Comes out close to 13".

Look at mounting specs. for your make and model on the internet.

HTH.

Re: Under Cabinet Microwave/Cabinet depth

#3

Re: Under Cabinet Microwave/Cabinet depth

Clint Searl, at the base of Haycock Mtn

>Buy the microwave first; they all come with full mounting instructions, and dimensions. I've done three different ones in my houses, and they all fit standard cabinets.

Clint

Re: Under Cabinet Microwave/Cabinet depth

#4

Re: Under Cabinet Microwave/Cabinet depth

Theresa K

>Clint, I did buy the Microwave. The instructions are for installing. I dont think they've adjusted for cabinet vs. microwave depth. Because if they did, I'm at a loss how. It's showing the cabinet flush with the microwave front. I've measured the depth of the unit myself and it is over 15".

There's probably something I'm missing.

Re: Under Cabinet Microwave/Cabinet depth

#5

Re: Under Cabinet Microwave/Cabinet depth

Jim Dillon

>Theresa,

I have a GE Spacemaker which is roughly 15 inches deep (excluding the handle). I built my upper cabinets (including one over the microwave) to a 13 inch overall depth (including exterior door) thus leaving about 2 inches for the microwave to stickout. Looks fine to me. Guess I could have made the rest of the surrounding cabinets 14 inches deep, but didn't see the need for it. Make sure you are not covering up any vents on the top. Hanging a microwave is a VERY cumbersome job and hard on the back especially if the stove is in place. Try to have an extra hand or maybe a car jack or something to hold the microwave in place - they are heavy. Hope this helps.

Jim

Re: Under Cabinet Microwave/Cabinet depth

#6

Re: Under Cabinet Microwave/Cabinet depth

RobV

>I have an under cabinet microwave that goes over the range and has a built-in exhaust fan vent. It's about 20 years old, but I don't think much has changed.

The front of the microwave sits proud of the face frame a good 2", because if it didn't the door would seem like it would bind when trying to open and wouldn't open a full 180 deg.

The cabinet above the unit is 13" deep (face frame to wall) and with the overlay door sticking out another 1" or so the microwave projection really isn't noticeable.

Re: Under Cabinet Microwave/Cabinet depth

#7

Re: Under Cabinet Microwave/Cabinet depth

Fred Davis

>Theresa ,

how soon you forget.

I sent at your request pics of our kitchen with the largest Microwave oven Amana makes and if you note it is flush in the trim kit and sits in the standard 12" deep upper cabinet and is very close to the Government recommended standard height of 48 inches from the floor.

I know it looks like magic but it is very simple once you have it explained.

It was a housewife who asked me if this was possible when we did her kitchen about 1976 and I thought about it for awhile and did not want to have the cabinet bumped out the depth of the Microwave because of the klutzy look and the increased chance of banging ones head on it. So that's how that came about.

For years we built the cabinet opening about a 1/4" shy of the oven and installed round Aluminum vents underneath for venting.

At first a vendor and then the oven people themselves started to make available trim kits which improved the look and the venting .

That's about it.

FredD

Re: Under Cabinet Microwave/Cabinet depth

#8

Moses Yoder

Re: Under Cabinet Microwave/Cabinet depth

Moses Yoder

>What is the make and model of your microwave? If it is a Kenmore then it will be difficult to get good specifications on it. Your owners manual should show if you need clearance for the door to open. Also, since you have the microwave already you could just clamp a piece of plywood to the side and see if the door rubs on it. If the door opens then the design is up to you. My opinion is that if it sticks out an inch or so it looks fine.

Re: Under Cabinet Microwave/Cabinet depth

#9

Re: Under Cabinet Microwave/Cabinet depth

Theresa K

>Fred,

I appreciated your taking the time to send me the pics of your charming kitchen. Your microwave solution, which works for your kitchen, is not quite what I had in mind for mine. I'm not planning on putting it into a wood box as yours. I failed to mention that my microwave is the over the range vent hood type.

I was hoping not to have to bump out the above cabinet, and it doesn't appear I will have to do that. That said, I have seen some cabinets with different depths that were lovely, & added a pleasing visual element.

You also suggested I have my cabinets professionally finished, instead of trying my hand learning to spray a finish. I went ahead & sprayed the maple plywood myself. Although it did take some practice, I am very please how they came out. I'm not sure how I'll finish the face frames, doors, & drawers yet. But I will be doing them myself too. I enjoy learning new things.

I learn new things all the time from this board. Most woodworking related, others way off topic...some very useful, some not so useful, but entertaining! This is my 'go to' board...thanks Ellis!

Re: Under Cabinet Microwave/Cabinet depth

#10

Re: Under Cabinet Microwave/Cabinet depth

Theresa K

>Thanks to all for the advice...This board rocks!

Re: Under Cabinet Microwave/Cabinet depth

#11

Re: Under Cabinet Microwave/Cabinet depth

Theresa K

>I bought a Frigidaire FMV157G. I will clamp something to the side, as you suggest, and see if it gets in the way off the door.

I dont mind it sticking out somewhat, but couldn't really picture it sticking out roughly 3" for 12" deep cabinets. I thought that would look awkward. Since my cabinets will be 14" deep, I'll be happy with just an inch or so.

I was in the middle of rough cutting the plywood sides yesterday, & hoping to head off any more mistakes.

Thanks for your advice!

Re: Under Cabinet Microwave/Cabinet depth

#12

Well, heck yeah, this place rocks!

Eddie Pacheco: San Jose, Ca,

>Glad you were able to get some quick and helpful advice to your question. I/we hope your kitchen project comes out looking nice and that you post a few pictures for us to see. However, I have a question. Some of us have done our own kitchens ----- and have taken maybe more than our wife's alloted time for the job. If you somehow take longer than you think for this project, any heat gonna come your way?.....:-0

Have fun in the shop.

Re: Under Cabinet Microwave/Cabinet depth

#13

Re: Under Cabinet Microwave/Cabinet depth

Fred Davis

>Theresa

I was glad to do it and it sounds like your well on your way to a "see what I did project"..

Sometimes it works well when you try something new like spraying finish the first time, but you had more nerve then I when I started it. I practiced a bunch ;-))

I have designed hundreds of kitchens and it always bothered me a little to see a microwave over a range for two reasons.

1. It's very high and difficult for women like my wife who is five feet tall to reach comfortably.

2. If you have a expensive range top like ceramic or glass, then just one dropped casserole will cost more then you thought possible.

Send some pics when your done.

FredD

Re: Under Cabinet Microwave/Cabinet depth

#14

Re: Under Cabinet Microwave/Cabinet depth

Theresa K

>Fred...Height in the kitchen will not be an issue for me or my family. I'm over 5'10", and it will be a welcome thing to use at that height! My daughter, who is the shorty of the family, is 5'7".

I'm going to risk the microwave over the range. I like the look, and I want that kind of glass/ceramic top electric range. Accidents happen.

Eddie...I'm sure to take more time than anyone to make/install my kitchen! But husband is just happy he's not the one having to deal with the kitchen, that any time frame is fine with him. He does know that when it comes to the electrical side, that will be his job. I don't mess with electricity. I'll do the plumbing, but he will deal with wires and be the muscle when I need it.

Now, if I could only get him to clean out his garage this decade ;)

Thanks all for your help!

Re: Under Cabinet Microwave/Cabinet depth

#15

Re: Under Cabinet Microwave/Cabinet depth

Fred Davis

>Now there's a Lady for all seasons....

FredD