Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Ebony Bending Question

Posts

Ebony Bending Question

#1

Ebony Bending Question

Jim Shaver - Oakville, Ont

>Hi,

I am trying to find an effective way to gently bend 1/8" thick, 1/4" wide ebony without cracking it as inlay in an an S shape... say a total of 3-4 inches long.

Any thoughts??

:-)

Thanks

Take Care,

Jim

Back Up the Bus Please

Re: Ebony Bending Question

#2

Re: Ebony Bending Question

Dick Coers

>I wonder about using a hot pipe like the luthiers use. Propane torch inside a piece of black pipe. Otherwise, dye some walnut, it'll bend unlike the "rock" called ebony.

Re: Ebony Bending Question

#3

Re: Ebony Bending Question

Sgian Dubh

>Which ebony?

If it's Diospyrus crassiflora, African ebony, it steam bends very effectively.

On the other hand Macassar ebony, Diospyrus celebica, is rather brittle and isn't a common choice for bending, with or without steam. Slainte.

Re: Ebony Bending Question

#4

Re: Ebony Bending Question

Jim Shaver - Oakville, Ont

>It's jet black Gabon

Thanks,

Jim

Re: Ebony Bending Question

#5

Will need to fabricate the "S"

Eddie Pacheco: San Jose, Ca,

>Minimal experience with that stuff, but I think the safe way will be to route out an "S" shape. Trial and error bending will be just as wasteful. Whichever way you go please show us the result.

Good luck.

Re: Ebony Bending Question

#6

Re: Ebony Bending Question

Sgian Dubh

>Gabon is a timber I've not heard of Jim, and my references on world timbers don't immediately or simply throw up a species with that name. I know of the country called Gabon, but that is different, although you might be referring to a Gabon grown species, eg, Gabon ebony which is the same as African ebony, ie, Diospyrus crassiflora , the species I said steam bends well in my last post.

Is there an alternative name, preferably Latin, so that I can double check my references and any pertinent information on the species? Slainte.

Re: Ebony Bending Question

#7

Re: Ebony Bending Question

Jim Shaver - Oakville, Ont

>Thanks for your help, I think it may well be one in the same. I have some trial pieces set up that I am going to steam and see if I am able to bend them. I will make sure to post results either way .

Thanks again All.

Take care,

Jim

Still wondering where my best friend went...

Re: Ebony Bending Question

#8

I am here.....! I am here.........! ;-)

HC Sakman

>

Re: Ebony Bending Question

#9

Re: Ebony Bending Question

Scott in Montana

>I too am wanting a tried and true method. My experience is that gaboon ebony has a strong will of its own and is not willing to bend, especally over a short distance.

I've given up and choose to ebonize other woods instead.

Scott

Re: Ebony Bending Question

#10

Re: Ebony Bending Question

Sgian Dubh

>Now you're confusing me further Scott. I've never heard of gaboon ebony, but I've used the species gaboon, Aucoumea klaineana . Gaboon is not black coloured, or even reminiscent of the ebonies, being pinkish brown and very light weight. This stuff is heading towards heavy balsa density and in my experience is used mostly in plywood construction. Slainte.

Re: Ebony Bending Question

#11

Issues with bending ebony

Ellils Walentine

>Couple things, Jim...

Gabon/Gaboon ebony should bend over a hot pipe in this thickness (1/8") but you want to saw your bending strips quite long so you have enough "tail" on either end to hold the strips while making the bends in the prime-time part of the strip. I used to have excellent luck with soaking the part of the strip in water where the bends would be, prior to actually offering them to the hot pipe.

Ebony is a very dense wood, so you can't force the process. Keep the strip moving over the pipe and replenish the moisture from a spray bottle whenever it starts drying out and you should be able to gradually create the curves you want, by rocking the strips back and forth on the pipe and being sensitive to their pliability. If they're absolutely resistant, cut your losses and laminate the strips from thinner stock. (It would be helpful to know the radii you want to bend.)

The other thing to know about hot pipe bending is that you will never perfectly duplicate a particular radius. All you want to do is approximate it, because you will be able to make it conform perfectly with your project with clamps and glue.

Ellis

Re: Ebony Bending Question

#12

This should identify it for you. *LINK*

Scott in Montana

>Check this link.

Scott


wood data

Re: Ebony Bending Question

#13

Re: This should identify it for you.

Sgian Dubh

>Fortunately Scott there is the Latin system of taxonomy which is exact; it turns out gaboon ebony, as at your link, is the same stuff I briefly discussed in my first post, Diospyrus crassiflora.

That's the beauty of the Latin: it eliminates all the confusion caused by local names, common names, vernacular names, and wrong names given to different wood species. Slainte.

Re: Ebony Bending Question

#14

AH! There You Are!

Jim Shaver - Oakville, Ont

>

Re: Ebony Bending Question

#15

Re: Ebony Bending Question

MikeW

>Hi Jim,

The only picture I have is of a box. The circular cut out shows a piece bent and glued in place. Don't have a picture of the completed box. This was done a few years ago and it has remained just fine.

For smaller pieces, I usually begin by placing the piece one the top of a container of wider where the ends of the piece to be bent barely overhang the container.

The container is placed in a microwave for several minutes on high, until the steam starts. The piece of Gabon then placed on the container. The microwave set to keep the steam rising off the container.

I can often get smaller pieces bendable in about 10 minutes. Really, it depends on how much steam is generated. Sometimes it takes a bend and remains, sometimes it takes a couple tries to fully bend it.

I use forms, even for smaller pieces. The forms are for both sides of the bend. Sometimes on a simple bend like this one, I use a solid form--here it was a ceramic coffee cup of a slightly smaller radius than I needed--and a strap to pull it around and tight. The cup then had hot water placed in it. Everything allowed to cool way longer than I thought was needed.

The Gabon stuff is still brittle, it really likes steam. On anything longer/wider/thicker, it takes a small homebuilt steamer using even a tea kettle, small pipe leading from the spout to a larger piece of PVC pipe.

I have also soaked pieces in broiler pan of boiling water for several minutes and had success--just make sure it is longer than needed like someone mentioned.

Oh, and wear gloves. The stuff is amazingly hot...

Take care, Mike


img

Re: Ebony Bending Question

#16

two more guitarmaker tricks

Michael Dresdner

>Luthiers bend ebony all the time, and as several people pointed out, it will bend on a hot pipe without too much fuss. We used to soak really troublesome pieces in concentrated ammonia, which turns it into something as flexible as rubber. You have to work fast and wear gloves, goggles and respirator, because the ammonia dissipates quickly, but you would be astonished at what it does to wood.

For box inlays, though, I would eschew the ebony and instead use vulcanized fiber, which comes in sheets in any color you want, including pure black, and in a wide range of thicknesses. The color goes all the way through, so cutting and sanding is not an issue, and it sands, cuts and bends cold without problems. It also takes all common woodworking glues and finishes. Many of the 'ebony' inlays on guitars, and many of the 'ebony' headstock overlays and inlays are actually vulcanized fiber. I have a whole mess of it in my shop and have been giving it away to box makers for years.

Re: Ebony Bending Question

#17

Hot Pipe Bending

Jim Shaver - Oakville, Ont

>Hi,

Thanks,

I was wondering if there is any good instructions out there on hot pipe bending...

Thanks,

Jim

Re: Ebony Bending Question

#18

Re: two more guitarmaker tricks

Jim Shaver - Oakville, Ont

>Thanks Mike,

I appreciate the input as well..

Take care,

Jim

Re: Ebony Bending Question

#19

Thanks Everyone!!

Jim Shaver - Oakville, Ont

>

Re: Ebony Bending Question

#20

where does one buy vulcanized fiber?

John K Jordan

>

Re: Ebony Bending Question

#21

Re: Hot Pipe Bending

Dan Donaldson

>You might take a look at books on building guitars or other musical instruments with curved sides. I have a heated pipe for bending wood and have made a few instruments with it. The main things that I have found is to keep the wood wet and keep it moving back and forth as you bend it to heat a wider area than just where you are bending. It really is not too difficult if you play with it a bit. The hardest thing that I bent was the herringbone inlay strips that I put on the bass that is in shop shots. It has two issues, first, it is wider than it is thick so you are bending it in the opposite direction that you would really want. The second is that it is glued together with soluble glue and you have to get it wet enough to let the internal structure slip (because the inside edge makes a sharper curve than the outside) without getting it so wet that it falls apart. For the bass, I had 5 pieces of various types of edging that had to be prebent and then simultaneously glued into the grooves around the edge of the instrument, three pieces of violin purfling (one bent the "wrong" way, that is across the wider cross section), the maple binding, and the herringbone.

The sides were also bent using the heated pipe, but the only real issue with these is the width, which is a bit over an inch wider than guitar sides. (they are koa)

Re: Ebony Bending Question

#22

Sources and another idea for wood *LINK*

David Barnett - SW Florida

>Firstly, if you do choose thin wood instead of fiber products, try this stuff. Works 'neat' or as a terrific steam-bending 'prep' on troublesome thin woods (watch the video):

http://www.joewoodworker.com/veneering/flattening.htm

For man-made fibers...

Knifemaker suppliers, such as Jantz Supply, sell sheets of vulcanized fiber for handle spacers:

http://jantzsupply.com/cartease/item-detail.cfm?ID=MI901

I prefer the long strips of fiber (a paper product) available from luthier suppliers, such as:


LMI - fiber purfling material