Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

OT: Lawnmower problem

Posts

OT: Lawnmower problem

#1

OT: Lawnmower problem

Dan Bundy

>It's a push mower (~11 years old) with a Briggs & Stratton engine. Has a primer bulb to push a few times before pulling the rope.

The engine will fire on the first pull, but only runs a couple of seconds and dies. After 4-5 cycles of this, it might run for 15-20 seconds. Finally it will run, but sputters for a while before sounding/feeling normal.

I'm guessing a dirty carburetor? I'm mildly handy. Is this something that I can learn to do myself? If so, can you recommend a good book, etc., to learn it from? Would a teaspoon or too of carb cleaner hurt anything?

Thanks in advance.

DB

Re: OT: Lawnmower problem

#2

Re: OT: Lawnmower problem

Kneale Brownson dreaming of snow in N. MI

>Just went through this with a mower that stumbled a lot the last half hour it would run and then got so it wouldn't run at all. I found the flexible tube between the air filter housing and the carburetor had aged (darn thing is only 14 years old) enough to split and allow dust to get sucked in. I replaced the tube, but the engine behaved just as you describe.

So I removed the carb, soaked everything in mineral spirits so I could scrub off the years of grime, took it mostly apart, blew out the orifices with the compressor, replaced the needle and seat (inexpensive kit) and reassembled with new gaskets (another inexpensive kit), and after ~$12 I had a running mower again.

Carbs on these things generally are quite simple. After cleaning up the outside, just take it apart on a good clean surface and note how everything goes. Blowing through the fuel intake removed the old needle valve seat for me and I used a rubber-tipped air gun to make sure there was nothing stuck in any of the other openings.

If you find the float to be something other than a hollow copper fixture, you might want to replace that too. The plastic ones tend to deteriorate over the years and with changes in fuel supplies.

Re: OT: Lawnmower problem

#3

Agree with Kneale...

John E in SC

>Cleaning a carb on a small engine is usually quite simple, and it's amazing how often that's the culprit. Don't think I would put carb cleaner in the gas, if that's what you were asking about. It's usually pretty simple to take the carb and soak it in mineral spirits as Kneale said, then blow out the orifices. Even if you don't put in the carb kit, just a decent cleaning can often work wonders. Don't forget to check / replace the fuel filter if your mower has one, and if it doesn't, you might think about putting in an "in-line" filter while you've got everything apart - might save you some grief down the road. Don't know of any books, but you probably don't really need one - just pay attention to how everything goes together.

Good luck,

John

Re: OT: Lawnmower problem

#4

JL

Re: OT: Lawnmower problem

JL

>Another thought - have you been putting Stabil in your lawnmower gas? I usually run all of my gasoline powered equipment with Stabil treated gasoline. I find I have less starting problems.

This doesn't mean your carb does need cleaning :). It may be that you have a little condensation built up.

Re: OT: Lawnmower problem

#5

Re: OT: Lawnmower problem

Orion

>Simplest first. Spark Plug. This is probably your problem. I have a friend that works on small engines and spark plugs are overlooked all of the time.

Re: OT: Lawnmower problem

#6

Definitely sounds like a dirty carb

Dan Mitchell

>Easy to OH with a kit from the local lawnmower place.

I suggest jet spray Gumout rather than mineral spirits. Much more aggressive solvent specifically for carburetor cleaning, plus the spray aspect is good for blowing out passages, etc. A compressor with a blow gun comes in handy too.

Cleaned many an automotive carb with this stuff, back in the day.

Dan

Re: OT: Lawnmower problem

#7

Re: OT: Lawnmower problem

Stuart Hough

>What about a rythmic "surge" to the running of the engine. I have a 4 year old Honda 5.5 hp mower and unless it's under a load (4" high, thick grass) it seems to pulsate about every 3-4 seconds. It will run up...act like it's trying to quietly backfire, the n start all over again. It starts easily with the automatic choke. I have cleaned the plug, no soot or greasy buildup was found.

Re: OT: Lawnmower problem

#8

Re: OT: Lawnmower problem

Kneale Brownson dreaming of snow in N. MI

>If you have good spark, the next thing that will cause operating problems is fuel/air delivery.

I'd change the air filter first and, if you get the same behavior, clean the carb.

Re: OT: Lawnmower problem

#9

Re: OT: Lawnmower problem

Dan Bundy

>Thanks for the input gents. DB

Re: OT: Lawnmower problem

#10

Re: OT: Lawnmower problem

iew

>Check the bulb. May have a small crack in it and that will cause the problems you describe.

Re: OT: Lawnmower problem

#11

Re: OT: Lawnmower problem

Randy Johnson Connersville IN

>Let's make this more intersting.

I have a brand new push mower with a Briggs engine that does pretty much the same thing. Granted, it's the cheapest one I could find. I bought it just so I wouldn't have to burn $4 gas hauling one from the house to the shop. The two are about twenty miles apart.

I prime it, pull the rope, and it will start and run for a few seconds before dying. If I start it and hold onto the handle to keep it running it will run while I continue to push the priming bulb. After maybe five minutes of this it will run without constant priming, but there isn't enough power to cut grass. Finally, after it has run for five or ten minutes I can use it.

Why don't I take it back? Because it is an hour and a half round trip to the place I got it.

Re: OT: Lawnmower problem

#12

Re: OT: Lawnmower problem

Kneale Brownson dreaming of snow in N. MI

>I'll bet there's some manufacturing do-do in the fuel system. If you can remove the float bowl, do that and see if there's anything floating in the bottom. If not, I'd try cleaning out the carb. I'd also run some fuel from the supply line for the carburetor into a clear glass container to see if there's any crud getting into there from the fuel tank. And if I didn't find anything or get any better performance, I'd return it. You might be better off getting a used mower from a local repair type guy. Many communities have someone who overhauls used mowers and resells them pretty cheaply. Then, if you have problems, your source is close by.

Re: OT: Lawnmower problem

#13

Re: OT: Lawnmower primer bulb problem

Kneale Brownson dreaming of snow in N. MI

>The primer bulb just serves to pull some fuel up into the carb for quicker delivery to the cylinder, doesn't it? A crack would just interfere with getting a good cold start, not with running after it starts. The fact he gets a start means the bulb is functioning, I'd think. The fact it won't continue running means there's something stopping the fuel passage through the carburetor.

Re: OT: Lawnmower problem

#14

Disassembly/Reassembly Tip

Ken Bellock (Houston, TX)

>If you are a bit nervous about taking the carb apart, and getting it back together the same way, do what I do. I have a cheap digital camera sitting on the bench next to me, and take lots of shots between each step as I disasemble everything. If you get stuck putting anything back together, just go back through the ordered shots to refresh yourself on how you got it apart. This is especially helpful if you can't get the whole job done in one day.

Good luck!

Ken

Re: OT: Lawnmower problem

#15

You have water in your gas.

Steve Schoene

>While this may not be the specific answer for this problem, it is generally quite universally true these days. Why, because of the ethanol in fuel these days. (One sample study showed about 18%average ethanol content in the New England region--and ethanol just pulls the water out of the air. Worse, in some conditions a "phase separation" occurs so that you get serious gunk and water. That's why Stabile is really, really recommended as a routine additive.

Re: OT: Lawnmower problem

#16

Re: OT: Lawnmower problem

Howard Schechter

>Carburetor issue. Could be several things. One I see often comes from leaving gasoline in the tank over the winter or actually even longer than about 30 days. It forms deposits which clog the carb jets. This is especially problematic with 2 cycle engines like on a Mantis tiller (a highly recommended tiller and I've used Troy bilts for years). Could also be a leak in the tube to carb from the tank which is an easy fix. Water in the gas could be the concern but then it might not start at all and would continue to be uneven in it's ignition of the gas.