Tony in Memphis - did you buy the PM?
JL
>Inquiring minds want to know :).
Knowledge You Can Build On — Est. 1998
Tony in Memphis - did you buy the PM?
JL
>Inquiring minds want to know :).
Ha!
Tony - Memphis
>Yes, but I'm not one to "gloat." And after being "attacked" for wanting one, I just thought I'd keep it to myself.
I do appreciate all of the input. This was a huge decision for me. Now I have a lot to do to get prepared. Get rid of the old saw, get a 220 outlet wired, figure out how the heck I'm going to get it off the truck, etc.
Tony
Re: And take pictures ?
Chuck in ND
>
Re: Ha!
Dan Mitchell
>I've had my PM2000 for about 9 months, I like it better each time I use it. It did require a bit of setup/tuning initially, especially regarding positioning/leveling the top. I have a very good FWW pdf on this I can email you if you'd like.
Welcome to the club!
Dan
Congrats! You'll never be sorry.
Scott in Montana
>
Re: Ha!
Tony - Memphis
>I have access to FWW online. I thought I had researched all of their powermatic info. I saw the video! I'd appreciate any help I can get!
Thanks!
Tony
Re: Ha! *LINK*
Dan Mitchell
>The article is generic, not specific to the PM, but covers all aspects of setting up a cabinet saw. In my case, I had to shim the front of the table nearly 1/8", in order to get the dial indicator in the miter slot to read parallel to the blade w/the blade tilted at 45, as it already did at 90. Most of the setup is fairly obvious, but this one wasn't (to me, anyway). Just to clarify, the article is:
http://www.taunton.com/finewoodworking/SkillsAndTe
Re: Ha! *LINK*
Dan Mitchell
>BTW I see FWW has a video displaying assembly of the PM2000. Near the end, they install the riving knife, anti-kickback pawls, blade insert & blade guard all at once, describing the process as "a little awkward", which it definitely is if you do it this way, which is not correct. I don't think you could even lock the riving knife in place this way, & I'm sure you'd have a helluva time getting it out like this if it were locked down. The easiest way is riving knife, insert, anti-kickback pawls, then guard. The effectiveness & speed/ease of removal-reinstallation of these bits is one of the reasons I got his saw, much better than the Unisaw I used to have in this regard.
Dan
http://www.taunton.com/finewoodworking/subscription/ToolGuide/ToolGuideArticle.aspx?id=25283
Re: Congratulations - may you have many safe years
JL
>of operation. Post some pics.
Getting it off the truck
David Yoho
>Tony, don't worry yourself about this. If it comes by local freight, be sure they bring it on a truck with a tail lift. I picked my cabinet saw up at the local store. They put it into the back of my pickup. When I got it home, I removed the tailgate, used a number of two-by-fours from the truck to the floor as a ramp, and with the help of another person we slid it down onto the floor with ease. At this point, further movement is difficult without a pallet jack or dolly but it isn't hard getting it off the truck.
David
Re: Ha!
Dan Donaldson
>For any tool, there is no reason to attack anyone over a choice. Sometimes you just want what you want, and if you can afford it, why not? Who cares what anyone else thinks. I have a pistol that costs over $2000. Do I "need" it? No, nor do I care what anyone else thinks about it either through their opinion or any perceived "bragging rights". I shot one and shortly after I bought one. I enjoy shooting it and can appreciate the craftsmanship in it. Never worry about getting a good tool or anything else.
We here all all interested in what others use and can take experiences into account when we make purchases of our own.
Enjoy your new toy and please post pics.
Re: Getting it off the truck
Glenn Madsen in the SF Bay Area
>We pulled my Unisaw off of the back of my pickup truck with an engine jack that a neighbor had. The bystanders were used as ballast for the base of the jack, more than anything else. Took ten minutes.
Three days later, Woodcraft called, and said my new saw was in, and did I want to pick it up. We shared a laugh about their paperwork.
Enjoy your new tools.
Re: Attack ?
Chuck in ND
>
Re: Attack ?
Ralph Turney
>Read Tony's first reply.
Thanks!
Tony - Memphis
>
Re: Attack ?
Chuck in ND
>Yeah, I red it and it doesn't make much sense, like the rest of his posts. I was defending the Contractors saw, if properly setup they are a good machine and are certainly capable of doing good work.
Re: Attack ?
Ralph Turney
>Yup,
I had a perfectly good "made in the USA" delta contractor saw that I replaced with a perfectly good "made in the USA" Powermatic Model 66. I don't regret it for a minute...my brother got to replace his aging Sears TS with my Delta saw and my x father in law got to finally get a much needed table saw (my brother's Sears TS). At the time we were in a financial situation to do this and even though I'm now divorced, I still have that 66!