Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Questions on Jet 14" bandsaw

Posts

Questions on Jet 14" bandsaw

#1

Questions on Jet 14" bandsaw

Bill Houghton, Sebastopol, CA

>Visiting from the quiet side...

As I mentioned in an earlier post, I've just acquired a Jet 14" bandsaw. A couple of questions:

1. The pin that aligns the table at the slot for removing/replacing the blade appears to be just a pin, not threaded at all. Is that right? Could anyone tell me the dimension of the pin? I think it's probably metric, and I suspect it'd be cheaper to buy a metric bolt the right side and cut off the threaded part than to buy a factory part.

2. Can anyone compare the factory blade guide blocks to Cool Blocks? Price, quality, etc.?

Re: Questions on Jet 14" bandsaw

#2

Re: Questions on Jet 14" bandsaw

Paul Waddle

>Bill,on the Delta bandsaw,its a taper pin. I would think it was the same on the Jet as they are very similar machines. The taper pin keeps the table from separating at the slot;ie,keeps it even. JMHO,pw

Re: Questions on Jet 14" bandsaw

#3

Re: Questions on Jet 14" bandsaw

Fred Davis

>plus cool blocks I run on my Delta are a significant improvement over the steel blocks it came with.

FredD

Re: Questions on Jet 14" bandsaw

#4

Re: Questions on Jet 14" bandsaw

George@Colonel's Workshop-Havertown PA

>Good Evening Bill,

I'm on my second Jet 14 inch Band Saw. I got a real steal on it ($150 includiong riser block). My #3 son has my original. Great saw.

Its a tapered pin. I replaced it on my 1st saw with a part ordered from Jet. I used the saw for 5 years without the pin, with no discernable difference.

Jet Blade Guards. Work fine as is. I replaced upper and lower guides on both saws with blocks of white oak. Every couple months I remove them and sand them square on my disc sander. No ned for anything different, they work fine and the price is right.

I also cut a port hole in the lower door and rivited a 4 inch dust port there. DC is now very effective.

George

Re: Questions on Jet 14" bandsaw

#5

Re: Questions on Jet 14" bandsaw

Chuck in ND

>Maybe I'm missing something or seting them wrong, but I'm not impressed with the factory blocks, whatever they are, they aren't very durable. I would think bearings would be better, maybe I'm wrong.

Re: Questions on Jet 14" bandsaw

#6

Re: Questions on Jet 14" bandsaw

Fred Davis

>George,

you are the only bandsaw operator I have seen besides me that did that.

When I had the DC installed in the shop I had a blacksmith buddy cutout the bottom door and put a five inch flanged collar on it and run a flexible plastic hose to it, like you say, that took care of the dust .

FredD

Re: Questions on Jet 14" bandsaw

#7

Re: Questions on Jet 14" bandsaw

DizD

>I have converted to ceramic guides on mine and I like them. Cost is about the same.

Re: Questions on Jet 14" bandsaw

#8

Re: Questions on Jet 14" bandsaw

Bill Houghton, Sebastopol, CA

>I note that the current Jet models have a 4" dust port cast into the body, below the cutting area. They've apparently learned from the woodworking community. This model's got a wimpy little port just next to the lower guides to fasten a shop vacuum on; I'll try that for starters.

Re: Questions on Jet 14" bandsaw

#9

For Starters

George@Colonel's Workshop-Havertown PA

>Hello Bill,

I was going to address that whimpy little proboscus issue. That littkle pipe lead me to the 4" DC port solution. The saw is pretty dirty as designed because the size of the old stock port was effectively only 1 1/2 inch wide and couldn't evacuate much dust even when coupled to a 4" DC reducer/coupling. Mountains of dust would accumulate on the lower guide bearing/thrust bearing assembly, as well as on the floor and inside the lower door. More importantly, it wound up coating the wheel tires. You can certainly use the saw effectively without the 4" port modification. It is not critical--but it sure is nice. It took about an hour to complete the job once I had the port and some gasket material. BTW, I just checked my new machine. I attached the port with sheet metal screws. The pop rivits were used on #3 son's machine.

George