Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Tip:sawing the lid of lidded boxes

Posts

Tip:sawing the lid of lidded boxes

#1

Tip:sawing the lid of lidded boxes

Bill Tindall, E.TN

>The best was to ensure that a lid on a lidded box fits is to assemble the lid and base as one unit and then saw the lid off. I have in the past always gotten some wiggles in the cut during the last cut when the lid falls off.

This piece is a domed lidded trunk. The funny parts that stick out to the left get curved to accommodate the domed top. Prior to making the last cut I put a spacer wedge in the 3 kerfs and applied tape as can be seen in the picture. Upon completing the last cut, as shown, the lid stays fixed and the saw doesn't nibble unwanted pieces from it. It came out perfect as a result of the tape and maybe a bit of good fortune.


img

Re: Tip:sawing the lid of lidded boxes

#2

Having a bit of a hard time following this...

Dan Mitchell

>So you make the 4 sides of the box and assemble it. You want a box with a 1" high lid, so you cut the last 1" off on the TS, one side at a time, then secure the 3 cut sides with tape & a spacer the size of the kerf (presumably 1/8") and cut the 4th side. So far so good (I think) but what's that lighter colored wood bit sticking out of the left side of the box just above the table? Is that part of the process, or part of the final piece? Maybe I'm being a bit thick here...

Dan

Re: Tip:sawing the lid of lidded boxes

#3

Re: Tip: another trick

North of the Border

>that box makers use is not to saw the sides all the way through but leave 1/32" or 1/64" wood. The lid is then cut off using a utility knife and any residue left is sanded flush.

Re: Tip:sawing the lid of lidded boxes

#4

Re: Having a bit of a hard time following this...

Don at Central Illinois

>The way I understand it is the off colored piece will be cut on a curve so the top is 'domed'. He just hasnt' cut the 'dome' part of the top. Clear as radar, at least I think that's what he is doing.

Re: Tip:sawing the lid of lidded boxes

#5

Even more fun...

Pat Evans

>It appears that you did a great job of dovetail spacing to allow for the kerf when you cut the lid. Even more fun is figuring the dovetail spacing when you cut the lid off an assembled box and then put a rabbit on the outside of the bottom and inside of the top to make a lid that closes more tightly and stays aligned.

Re: Tip:sawing the lid of lidded boxes

#6

Yet another Tip

Alan in Little Washington (NC)

>If you want the top to fit the bottom-

Before gluing the sides together, put a 1/4" - 1/2" wide dado around the inside faces. Make the dado depth one half the thickness of the stock at the point where you want to start your lid.

Assemble the box. Then cut another 1/4" - 1/2" wide dado around the outside a very tiny amount deeper the the inside dado. Offset it from the inside dado away from top by one dado width.

Use a box cutter to separate the sections and you will end up with a top that has an outside lip and a box with an inside lip that will fit together.


Re: Tip:sawing the lid of lidded boxes

#7

What a great Tip!

Dan Mitchell

>

Re: Tip:sawing the lid of lidded boxes

#8

Re: Having a bit of a hard time following this...

Dan Mitchell

>You're probably right; on 2nd look, I see the lighter colored bit is on the top as well as the bottom.

Re: Tip:sawing the lid of lidded boxes

#9

JL

Re: Neat tip!

JL

>Are we talking about a regular box cutter (utility knife) with heavy duty blades?

Re: Tip:sawing the lid of lidded boxes

#10

Re: Tis DVD has lots of tips and techniques shown *LINK*

North of the Border

>Your local library may have a copy to loan. Mine does.


Box making DVD

Re: Tip:sawing the lid of lidded boxes

#11

Have problem understanding how this trick works

North of the Border

>Could someone explain it please?

Re: Tip:sawing the lid of lidded boxes

#12

correct

Bill Tindall, E.TN

>The lighter colored piece will get cut to make the curved "gable" end for the domed top. It is lighter because it is reflecting the light more.

I puzzled as to whether I should cut the profile before or after assembly. I decided after and we shall see if that was a good idea. I will trace the domed top profile on these ends and cut on band saw.

Re: Tip:sawing the lid of lidded boxes

#14

JL

Re: Have problem understanding how this trick work

JL

>You have two dadoes. One on the inside of the piece that you cut before assembly. This would be "near" what will be the top. After assembly, you cut the other dado on the outside, just below where you cut the first dado. I'd make sure they didn't overlap.

This would give you two rabbeted edges (one inside, one outside) with the bottom rabbet fitting into the top.

Re: Tip:sawing the lid of lidded boxes

#15

Re: Thanks - So it's something like this

North of the Border

>Pic attached.

I guess it's this instruction "Offset it from the inside dado away from top by one dado width." that I got confused with. Thanks for you explanation.


img