Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Jessem Mast-r-slide

Posts

Jessem Mast-r-slide

#1

Jessem Mast-r-slide

Andy Lincoln,in Dearborn,MI

>Hi All,

I have an opportunity to purchase one of these units at a price that is significantly less than retail,and $70 less than Rockler's weekend discount of 15%. I am currently,using(and growing more fond of) a Format 4 slider while at work.This Jessem unit would be mounted to a Unisaw in the home shop.I realize it isn't the Format 4 but I think would be a good addition to the Unisaw.Unfortunately the seller does not have the unit mounted to a saw so I can't really try the action on the saw before purchase.Thought I would tap the collective knowledge here and bet I'll have better understanding within a day or two.

TIA,

Andy

Re: Jessem Mast-r-slide

#2

FWIW....I tried one at our Woodsmith store.....

Scott in Eastern Iowa

>........and if I had the room, this unit would be there. I believe this one was set up to the left side of the Unisaw too. The action is smooth as silk and she's a very impressive piece to add to any saw IMHO.

Buy it, I highly doubt you'll regret it.

Re: Jessem Mast-r-slide

Edited #3

Re: Jessem Mast-r-slide *LINK*

Garrett in Victoria

>My review of the MastRslide might be helpful to you. Click on the link below.


MastRslide Review

Re: Jessem Mast-r-slide

#4

Re: Jessem Mast-r-slide

Chuck in ND

>I know of a guy that is pretty happy with his, and I think Jessem makes some pretty good stuff.

Re: Jessem Mast-r-slide

#5

Re: Jessem Mast-r-slide

Rob Stokes in North Vancouver

>Garrett - haven't "seen" you around in a while. Out boating I presume?

Rob

Re: Jessem Mast-r-slide

#6

Ellis Walentine

By all means, check it out

Ellis Walentine

>Garrett's review is a classic.

Ellis Walentine, Host

Re: Jessem Mast-r-slide

#7

I bought one

McKay

>I bought one after seeing Garretts review and instructions to install. I left my extension on and use the slide daily. I don't care to use the fence on the front however, because the tape would be wrong. I also use metric a fair amount and wish that a metric/imperial rule were available.

Re: Jessem Mast-r-slide

#8

OK ..I own one now too!!...

Andy Lincoln,in Dearborn,MI

>I'm off to read Garrett's review once again and prep for a little shop time the next few evenings to have it up and running.

Thanks All,

Andy


img

Re: Jessem Mast-r-slide

#9

Re: OK ..I own one now too!!...

Chuck in ND

>Now wait just a cotton pickin minute. You can't claim a gloat with a catalog picture.

Re: Jessem Mast-r-slide

#10

Re: OK ..I own one now too!!...

Andy Lincoln,in Dearborn,MI

>C'mon Chuck the back seat of my truck just isn't very photogenic.

I'll take some photos of the unit and install as I get into that phase.I've now almost made myself feel that its ok to cut the rails on my bies fence(no room to shift them to the right,shop is too darn small as it is).

Andy

Re: Jessem Mast-r-slide

#11

Re: Jessem Mast-r-slide

Mark Valsi Pasadena Calif

>I have a love/hate relationship with mine.

It's a pain in the butt to have to move the "cross cut" fence out of the way to make a rip cut. And then to re-align the cross cut fence to dead on accuracy takes too much time. I did install a "set screw" in the cross cut fence to make it easier.

I don't like the way the measuring tape is held in place: it isn't !! it moves around and makes accuracy challengine.

I don't like the "stop" either. The incra system with 1/32 lock steps is much more accurate. The stop itself should have been designed much better.

But it is smooooooooth as glass on cross cuts, and small rips. and nice for big pieces of plywood or mdf.

I'm not sure I would buy it again . . .