Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

bandsaw tension

Posts

bandsaw tension

#1

bandsaw tension

Jeff Weaver

>I have a Grizzly G0555 14" bandsaw. Today I installed a Carter tensioning spring. I noticed right out of the box that the Carter spring is about 3/4" shorter than the factory spring. Sure enough, when I crank the handle to engage the tension spring, the tension indicator shows to be at the proper tension for a 1/4" blade and I can still slide the blade off the wheels with my fingers. Obviously, I will not be able to rely on the gauge with the new spring. So how do I know if I'm getting the proper tension and actually getting good use out of my new spring? And what is the danger of over-tensioning? Can I damage the saw? Or have I just goofed up on installation?

Thanks in advance,

Jeff Weaver

Re: bandsaw tension

#2

Re: bandsaw tension *LINK*

North of the Border

>Check out the FWW magazine article on tensioning your blade:

"If you don't have a tension meter, you can roughly tension the blade by eye. Raise the guides about 6 in. off the table and push the blade. The blade should deflect no more than 1/4 in." Follow the link and you can read the complete article.

In most cases, undertensioning rather than overtensioning is the issue. Many books actually advise people to tension the blade over what the setting shown on the bandsaw on the various sizes of blades because the settings are inaccurate. It is just my guess that in the extreme case of overtensioning, the blade will be weaker and there will be wearing out of the rubber tires?

Did you try to contact the supplier / manufacturer and see if they may have a solution for your problem. I don't you'd be the first customer who bought their accessory and came across this problem.


FWW

Re: bandsaw tension

#3

JL

Re: How are your ears?

JL

>You can follow North's suggestion from the FWW article to establish what your correct tension is. Thereafter, pluck the blade. You can tension by "ear" and hearing the note that the blade makes.

Re: bandsaw tension

#4

How important is tension?

Bill Tindall, E.TN

>Blade tension is not something I have paid a lot of attention to. I snug up the blade so it doesn't fall off the tires.

Does anyone have knowledge on what the effects of too little or too much tension are?

Re: bandsaw tension

#5

Re: How important is tension?

North of the Border

>The FWW article has this advice on too little blade tension for resawing:

"If the blade is not tight enough, it can bow in the cut, often ruining the stock."

Re: bandsaw tension

#6

Re: bandsaw tension

David Cockey

>Higher tension was the trend a few years ago, with the claim that bandsaw manufactuers don't know what proper tension is. Stronger replacement springs are supposed to be the answer.

More recently I've seen some claims that higher tension than necessary doesn't do anything beneficial, and is detrimental to tire, bearing and blade life. Perhaps the manufactuers have it right.

Re: bandsaw tension

#7

Re: bandsaw tension *LINK*

Howard Acheson

>First question, why are you replacing the spring? Was the one on the saw broken or damaged? There should be no need to change a spring.

Mark Duginske's latest bandsaw book will say that using the standard spring set to the saw's tension gauge dependent on the width of the blade is good enough. In the saws he had tested, the gauge was plenty accurate enough.


Duginske's new book

Re: bandsaw tension

#8

Re: bandsaw tension

Fred Davis

>I finally got around this argument a few years ago with a blade tensioning device sold by Carter that lets you tension the blade by raising a arm and releasing it by moving the arm down.

The device has a intermediate position to let you check for blade position while you replace one.

FredD

Re: bandsaw tension

#9

Re: bandsaw tension

Jeff Weaver

>I was having trouble with the blade bowing during resaw operations. I had read in a couple of places that this is usually caused by lack of tension. A stiffer spring seemed like an inexpensive fix.

Re: bandsaw tension

#10

Re: bandsaw tension

Jeff Weaver

>Thanks for the link, that article was helpful. I printed it out for future reference. I cranked up the tension until deflection seemed to be what was called for in the article. The blade I'm using is 1/2" and the tension scale is now past the 3/4" mark, but I seem to be getting a better resaw.

Re: bandsaw tension

#11

Re: Blade Bowing

Howard Acheson

>YOu may want to get Mark Duginske's new book. He spends some time explaining what causes imperfect cuts and the steps to take to correct them. Tension is only one issue with cuts that are bowing. Alignment, feed rate blade type and sharpness are all relevant issues and more often the culprit.

Re: bandsaw tension

#12

Re: bandsaw tension

Alex Grigoriev

>Read about resawing on highlandwoodworking.com. Blade bowing can be eliminated by fine tuning of the fence. And, of course, blade tension should be as high as possible, unlike when just cutting thin pieces.

Re: bandsaw tension

#13

Re: How important is tension? - depends

John K Jordan

>Proper blade tension becomes more important when cutting thicker wood, especially if it are green and tough. I have a riser block on a Delta 1" and a quick tensioning arm. When preparing very thick turning blocks if the tension is too low the blade will bow sideways in the cut especially when ripping with the grain. According to one book, in this situation the blade will bow until it finds it's own optimum tension, unfortunately increasing friction and making the cut very difficult as well as mostly worthless. This gets far worse if the blade is not well sharpened.

On the other hand, when cutting small amounts of thin, dry wood, I sometimes don't even activate the quick tensioning arm and the cut is fine.

JKJ