Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Forrest Blade Update

Posts

Forrest Blade Update

#1

Forrest Blade Update

Tony - Memphis

>I'm continuing the saga of my Forrest WWII that I sent in for sharpening...see previous thread.

Got a call from a guy yesterday (real nice fella, but I could barely understand his English - heavy accent). He said the only thing they found was that the blade had 0.005 runout (said that happens in shipment sometimes). Also asked if I was using a stiffener (this is a thin kerf blade). I said yes and he said good. He said he tested the blade and it did better with the stiffener. I thought he said they flattened it out some, but I'm not sure I understood him correctly. I was at work and couldn't quiz him too much. I did notice a similar amount of runout when I was playing with it.

It ships out today. I'm anxious to try it out. I'm also anxious to get my saw back! I don't have a good backup blade. I'll post with results when I get it back. I've been better than pleased with this blade for I dunno -ten years or so. I noticed Woodcraft has theirs on sale. I may order another one if/when I order the new saw - PM2000...maybe...still thinking. I've got some 2" teak I need to work with. Never used it before. Hope it doesn't give me any problems. I've never felt real comfortable sawing thick stock on this saw and I hear teak is pretty tough. I have cut some hard maple that was probably 1 3/4" though. That did ok, though I was nervous!

Thanks for all the suggestions.

Tony

Re: Forrest Blade Update

#2

Dale Lenz

Re: Thanks for the update, ?

Dale Lenz

>Did you ship the blade in a sawblade holder?

Re: Forrest Blade Update

#3

Teak...

John in New Mexico

>My experience with teak is it cuts up really nice. I sometimes get worried about thick maple on my ancient unisaw, more because it pinches than anything else. The teak I've worked with didn't move at all, and though abrasive wood, its almost waxy and cuts really smoothly as a result.

Re: Forrest Blade Update

#4

Re: Forrest Blade Update

Glenn Madsen in the SF Bay Area

>When you go to buying the new blade, you may give thought to using a regular kerf blade. They cut a wider swath, by a little, but the blade is stiffer, and resists heating up better.

That's what the sharpening guru at the blade shop told me years ago. My thin kerf blades had been purchased before I got the Unisaw. With 3 hp, there was no longer a need to 'save horsepower'. He was right.

Your heavier stock will thank you.

Re: Forrest Blade Update

#5

Re: Thanks for the update, ?

Tony - Memphis

>Actually, I packed it up much better than it came back. I work for a large shipping company, so I know what happens!

Tony

Re: Forrest Blade Update

#6

Re: Teak...

Tony - Memphis

>Thanks for that. That makes me feel better. I was just looking at tags at a new local wood source and their tag said teak was easy to machine. I'm building a garden bench, so I will be cutting a lot of large pieces.

I got a load of maple recently that pinched really bad. It pinched my splitter and stopped the blade. That'll make you pucker!

Tony

Re: Forrest Blade Update

#7

Re: Forrest Blade Update

Tony - Memphis

>Yeah, I was going that direction. I've been considering buying a PM200, so I figured I would get a full kerf for that one. Also thought about a ripping blade to rip thick stock down to smaller sizes, or at least for the roughing cuts. Forrest has a new ripper out.

Tony

Re: Forrest Blade Update

#8

Re: Forrest Blade Update

Ralph Turney

>I have a PM66 and that I use a 40 tooth and a 30 tooth WWII on (both .125 kerf). Often times when I put on the 30 tooth for some heavy ripping, it'll just stay on for everything, (I'm lazy) and works great. Even on cross cuts the 30 teeth make a great cut, I go a little slower, but it works fine. I also have a Freud 24 tooth rip blade that has been resharpened at Forrest that I ONLY use for ripping very thick stock...not the nicest cut line.

Ralph

Re: Forrest Blade Update

#9

Re: Forrest Blade Update

Binen

>I could be wrong but .005 runout doesn't seem that bad. I could see .020 or .030 being a problem but not .005.

Binen

Re: Forrest Blade Update

#10

Re: Teak...

Fred Davis

>Wouldn't be the one on the front of FWW May-June issue would it? ;-))

FredD

Re: Forrest Blade Update

#11

Re: Forrest Blade Update

Rick Jackson,TN

>Hey Tony, wish I had read your posts about the blade sharpening earlier...anyway, rather than send mine back to Forrest I took a chance and dropped mine off at the The Woodowork Shop in Bartlett. Floyd sends them out to some guy down there and I got it back within a week and at a very resonable price. The also sharpened a CMT blade I have. Best I can tell from the cut I got my moneys worth.

Re: Forrest Blade Update

#12

Re: Teak...

Jerry Gibbs

>teak contains silica and dulls cutting edges faster than other wood. otherwise it is easy to work with. Jerry Gibbs

Re: Forrest Blade Update

#13

Re: Forrest Blade Update

Tony - Memphis

>That's who sharpened my jointer blades! Last time, my knives got dropped behind his truck seat and he didn't find them for a while. He was much more upset than I was. Those were my backups, so I wasn't in a hurry. To be honest though, I wasn't real happy with the job he did. I did quite a bit of work to them after I got them back. I haven't been to that place in quite a while. Last time, I got very poor service (the younger fellow) and decided they didn't need my business. Probably petty on my part, but their selection wasn't that great either and the prices were kinda high.

I went to Craig Lumber Friday. Nice place. I think he was talking about you to another customer when he mentioned he had somebody come all the way from Jackson. He was excited about that! Gosh, they are some nice people. And their stock was beautiful. That bubinga up front was really something. I bought a nice piece of cherry. No project in mind, but it was so nice, I decided I had to have it. Hard to find good cherry around here. Colco hasn't much good stuff in a while. And Craig's appears to be S2S that is still close to 4/4! That's great. I can bring it home and clean it up to 3/4" . Very nice. I hope they can keep it going. I work about 5 minutes from there, so I can see a few lunch trips over there!

Tony

Re: Forrest Blade Update

#14

Re: Teak...

Tony - Memphis

>No, this one is my own design. I've been messing around with the design for a while. I was inspired by a couple of benches at place we go to on the beach in FL. I looked at a bunch of other designs and came up with something of my own. Nothing terribly exciting or unique. I did get the cushion first so I would know how tall to make the seat given the compression of the cushion. My wife and I are kind of pigmy like, so the bench height will be a tad shorter than standard. I built a mockup bench this weekend and tested it with the cushion. Turns out my guess was pretty good. Seat height is 14" + a 4" cushion that compresses quite a bit. This is one of the first projects I've really used Sketchup for. I did all my layout in Intellicad (2D) and then did a model in Sketchup just to see it all together. LEt me see if I can post it...ok it worked.

Tony


img

Re: Forrest Blade Update

#15

Re: Forrest Blade Update

Tony - Memphis

>Yeah, 0.005" sure doesn't sound like much. But the quality of cut was definitely not good and it was cutting on the back side. I'm anxious to get it back and try it out. I got a Masterplate and checked everything again this weekend. Everything is within a couple of thousandths (except my fence, which has a 0.0075" dip in the middle).

Tony