Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

fisheyes in lacquer

Posts

fisheyes in lacquer

#1

fisheyes in lacquer

allen heath

>I recently stripped a coffee table down to bare wood, sanded it smooth, cleaned it, applied stain, then brushed on lacquer...the problem is i got a lot of fisheyes in the first coat. I have ran into this problem before with poly, but not so in lacquer. The table was stripped clean, and yes, wiped clean, there was no residue on it at all. why would i get these fisheyes?

Re: fisheyes in lacquer

#2

After shave

Lee Schierer - McKean, PA

>Surface contamination is the cause. Do you use after shave? Fisheyes are commonly caused by silicone contamination. Some after shaves and shaving creams contain silicone.

Lee

Re: fisheyes in lacquer

#3

been there myself....

Bill Tindall, E.TN

>If the piece was ever waxed with a silicone containing wax the problem you see is to be expected, in spite of all the pretreatments. A drop of additive is all that is needed to eliminate the problem.

Re: fisheyes in lacquer

#4

Re: fisheyes in lacquer

Ed Mulligan, Cape Cod

>Some furniture products, Pledge for example, contain silicone. You maybe able to seal it in with spray coats of shellac.

Ed

Re: fisheyes in lacquer

#5

Re: After shave

allen heath

>my god.....i never thought of aftershave.....after the piece is clean, and before i put finish on, one thing i do is to run my hand over it to "feel the wood"....maybe that is how i got silicone on it....I am always very careful about silicone, as i have dealt with it in the past ruining a finish...but wow! i never thought about my aftershave...

Re: fisheyes in lacquer

#6

Re: After shave

Joseph Mulherin, Sr

>Allen, you also can consider your own body oils on your hands. This will cause the fish-eye too. Suggestion, get a bottle of anti fish-eye from your local auto pain dealer. Many paint shops use this as a protection of getting the fish-eye on the car bodies.

Re: fisheyes in lacquer

#7

That's Why I Grew A Beard

Ken Oakley-Sunny St. Cloud, Fla.

>No Razors, no shaving cream, no aftershave- No fisheyes.

Re: fisheyes in lacquer

#8

Ammonia ...

Joe Burke

>I'm doing some refinishing right now so I recently read that Michael Dresdner reccommends washing down with 1/2 cup ammonia in 1 qt of warm water as a final step before finishing. Specifically to remove oil and silicone. It's especially important if recoating with solvent or water based lacquer.

Paraphrased but it's on page 56 of Dresdner's book ... The New Wood Finishing Book.

I'm pondering this myself. I'll probably seal my stain in with a coat of vinyl sealer and top coat with conversion varnish. Been wondering if the vinyl sealer would seal in any contaminants?

Where are you Mike?

I'll probably wash with ammonia anyway, but inquiring minds want to know.

Re: fisheyes in lacquer

#9

Re: Ammonia ...

Sgian Dubh

>Shellac is a very versatile sealer if there's any suspicion of contamination in the groundwork. It's a tenacious finish that is a generally reliable barrier between anything dodgy below, within reason, and your preferred film forming top coat(s).

The only proviso is that dewaxed shellac is the safest bet as all film forming finishes adhere to it, whereas a minority of film forming polishes don't adhere well to waxy shellac-- water based finishes are one that don't like regular shellac containing wax. Slainte.

Re: fisheyes in lacquer

#10

Re: been there myself....

Steve Schoene

>I'd avoid the fish eye eliminator except as a last result. It is basically a hair of the dog that bit you, a step down the road toward addiction. Once you start introducing silicone into your spray gun. and its overspray it's hard to eliminate. I'd go with the barrier of dewaxed shellac, though under basic NC lacquer it won't matter.

Re: fisheyes in lacquer

#11

Re: Ammonia ...

Al Stokka - Cambridge, Iowa

>Joe,

I had a problem with fisheyes in an oil-based polyurethane finish. Michael Dresdner offered the following information, Mid-April, 2007:

The solvent for silicone oil is mineral spirits. Scrub contaminated raw wood with liberal amounts of mineral spirits and sop up as much as possible (don't just spread it around.) Follow that with a scrub of liberal amounts of warm water laced with household ammonia, which is a surfactant for silicone oil. Again, mop up as much as possible. This one-two punch will remove the lion's share of the silicone oil.

I followed his advice and while it worked, I didn't not strip the previously applied coats of poly. Therefore I had to deal with the divots in the previous poly finish. Many rounds of sanding to smooth without cutting through the finish and applying additional coats of poly. If I had to do it again, I think I'd strip the finish and start anew.

Good luck,

Al

Re: fisheyes in lacquer

#12

Re: Ammonia ...

Joe Burke

>Thanks RJ/SD

I figured I could follow the axiom that ... shellac, or Sealcoat, works when nothing else will. However, I'm wondering if a good vinyl sealer will do the same thing.

Re: fisheyes in lacquer

#13

Re: Ammonia ...

Sgian Dubh

>Vinyl sealer is good too, but perhaps not quite as forgiving of contaminants as shellac is. A somewhat less than desirable element of vinyl sealer in my experience is a slight tendency to cloudiness. Slainte.

Re: fisheyes in lacquer

#14

Naptha......................

howard

>My understanding was that a rubdown with naptha will remove any silicone residue. I also agree with the dewaxed sealcoat as a barrier coat.