Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

steam bending bowed arm Morris Chairs

Posts

steam bending bowed arm Morris Chairs

#1

steam bending bowed arm Morris Chairs

mike@american sycamore

>I have the Delta team here this week at American Sycamore and we are building eight bowed arm Morris chairs. We are steam bendng the

1 1/8" x 6" x 42" quarter-sawn white oak arms. Thanks for the tips I got here at WoodCentral I buit a steam box from 3/4" Marine grade plywood. I covered the outside of the box with 1" stroyfoam.

I bought two new 5 gallon heavy duty gas cans and with a propane industrial torch under the filled with water gas cams I boil the water. I have two hoses going into the botom of the box from the cans. Using a meat thermomitor we bring up the heat to 220 degrees then load four pieces of wood and heat for 70 plus minutes.

We have found that you have to work quickley because when you open the door the heat drops quickley. We load the arm pieces on a form and clamp down while one student stands on the board bringing it down to the curve and then clamped in place to dry over night. So far we are batting 100% with 12 arms bent. It is so cool seeing that wood bend into shape.

I am looking for a way to build a steam box that I can heat with an electric commercial hot plate so I can bend in doors at shows. If anyone knows of a source for a used commercial hot plate that will boil water for 70 plus minutes on a commercial scale please let me know. Thanks,

Mike

Re: steam bending bowed arm Morris Chairs

#2

Re: steam bending bowed arm Morris Chairs

Mike Jurnigan in Suffolk

>Mike,

I have been doing steam bending demos with the Windsor chair bows for right many years. The main problem, as you noted, when you said about your current rig, is when you open the door, the temperature drops rather quickly; is a lack of volume. I have tried wooden boxes, and PVC pipe. I have tried various assortments of hot plates and pots to use as a boiler. The drawback that I saw on most OTC hot plates was they have a limit switch that prevents them from running continuously. I eventually bypassed those on the units that I used. However, the best I could get was a simmering boil. You really need a rolling boil. I believe a 220 volt unit would work better. If you get a unit from an electric range that had two burners that dropped into the range as a unit, and had an enclosure built to hold it to make the Fire Marshall at the shows happy, you might have better luck. I just never took the time and was willing to spend that much to experiment.

My current setup, which works excellent for Windsor bows, consists of a piece of 4� heavy wall PVC pipe with 2 of the Lee Valley steam kettles (Which they no longer sell. They also were at rated at either 1200 or 1500 watts each) with 1 connected at each end by radiator hose. With this rig I can steam a bow or a comb in less than � hour. If you would like to see a photo I will send you one. I seriously doubt if you will have much luck doing multiples at the same time at a show. The problem is getting a rolling boil of water quickly and being able to sustain it. My experience has been the more agitated the boil the better it carries the heat to the wood.

If you have any question e-mail me.

Mike in Suffolk, VA.

Re: steam bending bowed arm Morris Chairs

#3

Re: Electric Kettle?

Kneale Brownson dreaming of snow in N. MI

>Maybe yard sale/flea market hunts for an electric kettle. All the newer ones shut off when the water boils, but I think the old ones will boil themselves dry. Some of those came with a round spout you could clamp a radiator hose to. Don't you also need a return line for the condensate?

Re: steam bending bowed arm Morris Chairs

#4

Re: steam bending bowed arm Morris Chairs

Ed Mulligan, Cape Cod

>Mike -

I recently attended a chair making class which included steam bending some of the chair parts. We used two wallpaper steamers to provide steam to the approximately 12 x 12 x 48 plywood box. Worked very well.

Ed

Re: steam bending bowed arm Morris Chairs

#5

No experience with electric, but some thoughts

Keith Newton, LR, Arkansas------WebKitFormBoundary

>On dealing with the time limit. Naturally you want to have your compression straps set to the wood before they go into the chamber.

You didn't mention using end compression / backing straps, and may not need it for this slight bend. However if you have spring-back, later, this may be why.

Again, you shouldn't need it for this, this time of the year, but for cold weather, and deeper bends that require more time to get straps and tackle on before even starting the bend. I have not done this yet, but I have been thinking of trying to find something to insulate the wood to keep the heat in. A readily available product would be aluminum foil, which seems to offer a lot of possibilities.

The foil could be laid out so when the wood comes out of the steam, it could be rolled up in the foil. That would shut out the air, which would stop the evaporation, which is the main type heat transfer here. While aluminum is a good conductor, it would not give any up to radiation, because shiny metallic surfaces just don't loose it that way like darker surfaces. It would however give it up to the air by conduction through the foil, but not much compared to the evaporating moisture. Stainless foil would be better but the cost is high.

Naturally I would score and tear away the foil after the clamps are on to allow evaporation and heat loss to go as would be normal.

I don't know if others have tried this, or have other methods. I would like to hear them if you do.

Re: steam bending bowed arm Morris Chairs

#6

JL

Re: steam bending bowed arm Morris Chairs

JL

>I use a "turkey frier" base. I picked it up after the turkey frying craze passed.

I currently use a 5 gallon propane tank. I'd go for a small one to make it more portable.

Re: steam bending bowed arm Morris Chairs

#7

Re: Electric Kettle?

Mike Jurnigan in Suffolk

>No, it's a losing battle. There is a vent in the bottom of the Boax/PVC pipe. Also not a good idea to pressurize.

Mike, if you are interested I have plans for a safe pressurized steam box.

Mike in Suffolk, VA

Re: steam bending bowed arm Morris Chairs

#8

Re: luthier's approach?

mike hamilton

>Hi Mike,

I wonder, for your show purposes, if there would be a way to steal an idea from modern luthiers. Granted they usually bend thin stuff, the idea of using heating blankets might be something you could use as a starting point. It'd be slow, but it'd be electric. You don't have to get the lignin up to 212F to get the wood to bend. If I recall correctly, you only need about 145F - but all the way through the piece.

Regards,

Mike Hamilton

Plainfield, IN (just up the road a piece...)

Re: steam bending bowed arm Morris Chairs

#9

Re: No experience with electric, but some thoughts

Kneale Brownson dreaming of snow in N. MI

>Wouldn't there be foil on the back of the stock where it presses against a form? Would that part dry out more slowly than the exposed stock after you tear off the foil?

Re: steam bending bowed arm Morris Chairs

#10

Re: No experience with electric, but some thoughts

Keith Newton, LR, Arkansas------WebKitFormBoundary

>Yes, but it normally doesn't stay on that form very long. Once it has set, it can be moved to another form which allows more air to get to it to dry, but be constrained against spring-back. Leaving it on the bending form long term would be like stacking wet lumber dead, rather than stickering it.

Re: steam bending bowed arm Morris Chairs

#11

steam bending .........thanks

mike@american sycamore

>A BIG THANK-YOU To everyone for excellant advise....thanks,

Mike