Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Installing Shelix Head for Delta 37-380 Jointer

Posts

Installing Shelix Head for Delta 37-380 Jointer

#1

Installing Shelix Head for Delta 37-380 Jointer

David Yoho

>I had several requests to document replacement of the original three-knife cutterhead on my eight-inch Delta model 37-380 jointer with the new Byrd Shelix cutterhead I purchased from Sunhill Machinery.

The process is fairly simple but there are three documents that I found helpful for removal and installation. The instruction manual that comes with the jointer has all the adjustment and assembly information you'll need. The Delta parts breakdown list is also helpful for identifying parts and where they go. The final document is the Sunhill Cutterhead Installation PDF File from Sunhill's Website, which I printed and took to the shop.

I started by unplugging the jointer, disconnecting the four-inch dust collection hose, removing the rear cover and V-belt. Then I used the allen wrenches supplied with my jointer to remove the allen head bolts to all the assemblies and brackets to allow access to the end caps of the old cutterhead. The PDF file shows a good diagram of the old cutterhead and how to remove it.

With the cutterhead removed, this is how things looked:



Here's what's in the box from Byrd Tools - a Torx bit, screwdriver handle, five extra carbide inserts, and instructions for insert removal/rotation. It also came with the bearings already installed on the cutterhead shaft.



Here's a shot of the original head, the Byrd head, and the printed PDF installation instructions.



These are the left and right supports/end caps cleaned and ready to go.



The supports/end caps slipped right over the respective bearings and are now ready to drop back into place.



The hex nuts and washers (one on each side) for the support studs are ready to be tightened.



After checking that the cutterhead was level with the outfeed table on both sides, I tightened the hex nuts. The instructions say to shim if necessary. You can use a block of wood when checking for level but I used my Lee Valley straightedge. It turned out that mine was level and did not need shimming. This is an important step because, unlike the standard cutterhead, the inserts of the Shelix head are not adjustable up and down, so it's very important that the head be level with the table.



Next, I installed the pulley by placing the key into the shaft's keyway and tapped the pulley onto the shaft, being careful to align it with lower pulley, and then tightened the two allen screws.



I re-installed the section of the infeed table that the blade guard mounts to. Alignment is facilitated by two pins. I used a soft-faced hammer to tap the assembly on before installing the allen bolts. I put a little blue Locktite on the threads before installing them because originally they had some on them when I removed the bolts.



I followed the same procedure for installing the cutterhead pulley guard/carriage bracket.



I mounted the fence carriage assembly to the cutterhead pulley guard/carriage bracket next.



Finally, I attached the fence to the fence carriage assembly and installed the blade guard and adjusted the spring tension so the guard would return properly. At this point all that is left to do is to put the rear cover back on, attach the dust collection hose and clamp it, and plug in the jointer's power cord.



I adjusted the infeed table height where I wanted it and the outfeed table just a little. I then turned on the jointer and tested the outfeed height adjustment to the cutterhead by running a piece of stock on its edge. I got a little snipe on the trailing edge on the first few passes. I kept adjusting the outfeed table height until this disappeared completely.

With the adjustments made, I ran a piece of aromatic cedar with a big knot on one part of the edge across the jointer. Normally my old cutterhead would tear or take chunks out of knots like this. The Shelix head cut it like butter and left it smooth and defect-free.

Now it was time for the real test - a piece of highly figured tiger (curly) maple. I ran one face first, then an edge. There was absolutely zero tear-out anywhere and the cuts were super smooth. The finished surfaces looked just like they do after using a hand plane or scraper on wood. The surfaces had that just-planed sheen to them that made the figure jump.

While the Byrd Shelix head is a bit pricey, I did get it at a $60 discount from Sunhill, which saved a bit of money. However, after seeing the results I got, I think it would have been worth every penny at full price. I have to say this cutterhead performs as advertised and it's one of the best upgrades I've made in my shop in a long time.

David

Re: Installing Shelix Head for Delta 37-380 Jointer

#2

JL

Re: Thanks for the "article".

JL

>Maybe I should consider upgrading eventually. Hmmm I wonder if they make Shelix cutters for hand planes :).

Re: Installing Shelix Head for Delta 37-380 Jointer

#3

David I have question about the upgrade

McKay

>I currently have a 9 month old dj20. I purchased the dj20 because I have had 2 of them at the school I teach at for about 25 years. I had no reason to look further. However, I purchased the PM8" helical at the school and found the cut so superior to the dj20 that now I regret buying the dj for myself. By the time that you figure your time, the cost of the head and the depreciation, would it be about the same cost to buy the pm helical that has a longer fence?

Re: Installing Shelix Head for Delta 37-380 Jointer

#4

about cut quality

Tom Sontag - St. Louis

>I am aware of the superior treatment of gnarly wood, but was surprised to see you write that "...the cuts were super smooth. The finished surfaces looked just like they do after using a hand plane or scraper on wood. The surfaces had that just-planed sheen to them that made the figure jump."

I have seen several boards that came off of a commercially used setup and there was definitely short ripples (as opposed to the long ripples from a conventional head) along the board. I am guessing that you pushed the wood across much slower than these get-r-done types in a commercial setting.

This is all A-okay; I just want people to know that you need to take the final pass slowly to get the kind of result you refer to. Did you run the tiger maple over backwards?

Re: Installing Shelix Head for Delta 37-380 Jointer

#5

Yep

Dan Donaldson

>The cutter for a hand plane is called skewing it ;-)

Re: Installing Shelix Head for Delta 37-380 Jointer

#6

Thanx, Dave!

Stuart Hough

>Looks like everything went pretty smooth amd straightforward. We appreciate the pics and narration. It'll make the job easier if/when any of us plan on the same thing. Thanx again!

Re: Installing Shelix Head for Delta 37-380 Jointer

#7

Re: Installing Shelix Head for Delta 37-380 Jointe

Brent in Montreal

>Thanks David, looks like a straight forward assembly. I was worried about the end caps fitting,but you seemed not to have a problem. Two questions; Is your jointer USA made or a newer version? When you ordered the head did they ask about this, I'm wondering if there is a difference in bearing size, metric versus standard?

Re: Installing Shelix Head for Delta 37-380 Jointer

#8

Re: David I have question about the upgrade

David Yoho

>That PM jointer looks like a very nice machine indeed. I don't have any direct experience with it or the DJ-20, both being parallelogram style jointers. My Delta model is not a parallelogram and I'm not sure what difference it makes in the end. My assumption is, since you have used both the DJ and the PM, the helical cutterhead is what makes the difference you're seeing. Personally, at about $2300 for the PM, if I already had the DJ I think I'd add a Shelix head to it and not look back.

David

Re: Installing Shelix Head for Delta 37-380 Jointer

#9

Re: about cut quality

David Yoho

>Tom, thinking back to yesterday when I was running those test pieces, I suppose I may have been feeding them a little slower than normal because it was new to me and felt a little different than what I've been used to. However, like you say, I usually like to run my final pass a little slower to improve the finish. I'm still very new to using this Shelix head and will need to work with it a lot more to get the right feel for it. I've been cutting with the standard type of head forever and knew how to push the stock when I was trying to get the best finish of cut.

David

Re: Installing Shelix Head for Delta 37-380 Jointer

#10

Thanks, Stuart

David Yoho

>When I was doing some research to see what others encountered installing this Shelix head, I wasn't able to find anything helpful for my specific jointer other than it was straightforward and to follow the parts diagram. Being a visual type, I was looking for something like I put together. That's not to say I did an exhaustive search but I didn't find anything.

I think the design of the Delta 37-380 is probably much like many of the other brands in that type of jointer and hopefully someone will find my experience informative for their own situation if the time comes.

David

Re: Installing Shelix Head for Delta 37-380 Jointer

#11

Re: Installing Shelix Head for Delta 37-380 Jointe

David Yoho

>Brent, when I removed the end caps I cleaned them up with some mineral spirits, wiped them dry, and ran a piece of gray Scotch Brite around the inside. Before installing them onto the new bearings I used my finger to wipe a thin coat of light machine oil on the inside surface making contact with the bearing. They slipped on snug but with ease.

As far as where mine was made, I don't know for sure but would guess off-shore. If I remember right, I purchased it in 2001. The folks at Sunhill had to call Byrd to see if they had the head for the 37-380 in stock. When they returned my call, they did not ask where it was made or for a serial number. All they needed to know was the model number. I assume that Delta used the same specs whether they were made here or overseas.

David

Re: Installing Shelix Head for Delta 37-380 Jointer

#12

Re: Installing Shelix Head for Delta 37-380 Jointe

Brent in Montreal

>Thanks for the info David. I think you've pushed me over the edge. I'll be giving Sunhill a call tomorrow.