Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Good sharpening service in Seattle area, anyone?

Posts

Good sharpening service in Seattle area, anyone?

#1

Good sharpening service in Seattle area, anyone?

Dan MItchell

>Recently got a PM jointer. Since I'm somewhat new at this whole woodworking thing, I've been "practicing" on some cedar 1x3 material from a hot tub which I ripped out awhile back. I've actually made a couple fairly nice bits with the bits, but I overlooked something when machining the boards. The tub had been nailed together with hot dipped galvanized nails, and while I was careful to remove the NAILS before running the boards through the jointer & planer, I overlooked the bits of ZINC which often remain in the nail holes. Consequently, the blades of my new jointer & planer now are a bit nicked. Below is a pic of 2 of the larger nicks on a jointer blade. The planer (DeWalt 734) has reversible blades, so that's not too huge an issue, but the jointer blades are going to need to be re-sharpened. SOOO, I'm wondering if anyone happens to know of a good place in the Seattle area to take the blades to for this.

Any other thoughts on this situation appreciated.

TIA

Dan


img

Re: Good sharpening service in Seattle area, anyone?

#2

Re: Good sharpening service in Seattle area, anyon

Rob Stokes in North Vancouver

>I used to drop them off at the Sumner Woodworkers store and pic them up a few days later. They always came back sharp.

But before you do that, see if you can index the blade left or right from each other. Chances are you can and if so, you can run those blades for a while longer.

Rob

Re: Good sharpening service in Seattle area, anyone?

#3

Ouch!!

David Yoho

>Dan, sorry to see your knives got nicked like that. I don't have any recommendation for a sharpener in your area. I have a spare set of knives for my Delta jointer and always sharpened my own with my Tormek and swapped them when that happened.

I just put the original head in the wooden box my new Byrd Shelix head arrived in today. Looks like I won't be needing to sharpen jointer blades again. Maybe one day if I purchase a larger planer than my Delta 13", I will be able to use that expensive Tormek jig for planer/jointer blades again. That jig is one of the most expensive ones they sell!

Pictures and write-up coming on converting the cutterhead hopefully tomorrow when I have more time.

David

Re: Good sharpening service in Seattle area, anyone?

#4

Re: Good sharpening service in Seattle area, anyon

Dan MItchell

>Rob-Shifting the index seems like a good possibility, 1st I have to bone up on the whole process of setting blade height, etc.

Dan

Re: Good sharpening service in Seattle area, anyone?

#5

Forest knows of a good one

Dustmaker Mike

>in near Bermerton. Come on Forest help out a fellow PNW'ner

Re: Good sharpening service in Seattle area, anyone?

#6

Eastside Saw & Sales

Doug Reynolds in Seattle

>Try Eastside Saw and Sales, 12880 Bel-Red Road, Bellevue 425-289-0112 or, 1-800-962-0279. I have also used Woodcraft as they are closer to work. They also make up my Lennox bandsaw blades.

Re: Good sharpening service in Seattle area, anyone?

#7

Re: Eastside Saw & Sales

Dan Mitchell

>Thanks for the reply, Bellevue's not too far.

Dan

Re: Good sharpening service in Seattle area, anyone?

#8

Re: David

Larry Clinton At Frankfort (Central)., Indiana

>I sure wouldn't purchase a larger stationary planer with anything but segmented carbide cutters. Either Grizzly or Byrd. I say this as one who has the Grizzly 8" joiner with the carbide cutters and a 20" Yorkcraft planer with the Byrd head. In reality the planer is far more important to me than the joiner as far as cut quality. I only use the joiner to flatten a face enough to assure I can end up with a straight board out of the planer. Then I plane the second side on the planer and back to the first side with the planer - alternating until I obtain the proper thickness. At that time all the joiner cuts have long since disappeared. The carbide cutters on the joiner do do a great job on the edge - but I normally use my WW2 on the second edge - rarely do I return to the joiner - If I am concerned about the edge at that time I may use a hand joiner plane. I could always resaw the second edge (the one from the joiner) if necessary. If I have wide boards that have no bow - a little cup will plane out -than I will bypass the joiner and actually do both faces on the planer. Then go back to the joiner to straighten the edge. Not saying I wouldn't purchase another joiner with the carbide blades, just that the planer is more important the way I work.