Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Glue Line RIP Blades/Jointer

Posts

Glue Line RIP Blades/Jointer

#1

Glue Line RIP Blades/Jointer

George@Colonel's Workshop-Havertown PA

>Good Morning all,

Yesterday I did a lot of planing, jointing and ripping. I have a 10" Freud rip blade in my Jet Hybrid. I use the Freud for preparation of rough stock, and to save wear on my Leitz and Forrest combo blades. After I got all boards to S4S, and sequenced for glue up into panels, I still had some which needed further ripping. While the blade uis clean and fairly new, the cut was pretty rough, and that required another visit to the jointer. I am wondering if a glue line rip blade would save that final step. Every time I need to use the jointer, I have to pull it out of the laundry--after I push back the table saw against the wall to make room. My arthritis bothered me yesterday and it was a hassle. Questions: are the glue line rip blades worth the investment? Can they be used in lieu of a jointer to clean up/rip a board to final dimension?

George

Re: Glue Line RIP Blades/Jointer

#2

Re: Glue Line RIP Blades/Jointer

Mark Mandell - Gone Round In Jersey

>George,

I use a Systi Glue Line rip blade. Does very well

but,

In my view there's just no substitute for a properly jointed glue face.

mm

Re: Glue Line RIP Blades/Jointer

#3

Re: Glue Line RIP Blades/Jointer

Lee Schierer - McKean, PA

>Before I inherited my jointer, I often glued up boards that had been ripped on my TS and none of those joints have failed. As long as the cut is smooth and you don't have deep tooth marks, it should glue up fine. I will admit that I run nearly every board across my jointer now that I have one. You can also get a good glue edge after ripping with a single pass of a good sharp hand plane. Just make sure the blade is sharp and the blade is set square to the sole.

Lee

Re: Glue Line RIP Blades/Jointer

#4

Re: Glue Line RIP Blades/Jointer

Clint Searl, at the base of Haycock Mtn

>If the unclamped dry fit coming off the saw is good, running the boards over the jointer is superfluous at best and could introduce its own rendition of gaps.

Clint

Re: Glue Line RIP Blades/Jointer

#5

JL

Re: Glue Line RIP Blades/Jointer

JL

>I don't have a glue line rip blade. I do have a jointer and I do have a couple of #5 planes.

If it isn't good enough coming out of the table saw, I will often dress it up with the #5. I only use the jointer on occasion (but I do use it if necessary).

My $0.02.

Re: Glue Line RIP Blades/Jointer

#6

Re: Glue Line RIP Blades/Jointer

Mark Mandell - Gone Round In Jersey

>Even though I keep my blade reasonably clean, I think a TS blade will most always put some glaze on a sawn glue joint. The jointer removes that nicely. A properly done jointer-cut will also give sharper edges.

I also find it easier to set and hold a consistent 90� cut with the jointer fence.

If one is getting gaps in jointed edges, they need to retune their machine or watch their technique.

YMMV |;-}

Re: Glue Line RIP Blades/Jointer

#7

Re: Glue Line RIP Blades/Jointer

Ken Platt (Granby, CT)

>I have the Systimatic "Glue Joint Rip" blade. I've never been able to get rips as smooth as I like for a glue up with it; the edge is just rough to touch. The jointer leaves a much smoother surface for me. It's possible that I could glue up off the saw and the joints might be ok, but I prefer the security of the smoothest edge I can get for glueups. However, if I had to haul out the jointer every time, I'd probably try to use the edge off the TS and see.

Ken

Re: Glue Line RIP Blades/Jointer

#8

Re: Glue Line RIP Blades/Jointer

Robert R Clough - Thorncraft

>Well, George, I have a glue line blade which has always worked well for me. However, my Forrest II works just as well. I have no jointer or planer so, if I am not sure, I use my hand jointer or set up my JoinTech as a jointer.

But the saw generally does an adequate job.

Re: Glue Line RIP Blades/Jointer

#9

Re: Glue Line RIP Blades/Jointer

Dave in Haverford PA

>Hi George! I use a Freud thin-kerf rip blade now and rarely the jointer. On the TS the cut is ALWAYS square and there's no snipe. Glue face is very smooth.

Re: Glue Line RIP Blades/Jointer

#10

Re: Glue Line RIP Blades/Jointer

Larry Clinton At Frankfort (Central)., Indiana

>George, my WW2 sure seems to normally produce a glue line edge on most woods. Occasionally when sawing Cherry, or some white oak I will get a glaze or burn (probably my feed rate through the blade or I failed to clean the rosin - blade got a little gummy). I have glued up several panels without any issues to date, although I do sometimes run the edges through the joiner - alternating the face against the fence to insure all error from 90 degree is eliminated. Once in a while I will use a hand plane (usually on short pieces as I am sure not an expert in staying at 90 degree).