Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Tablesaw lubrication

Posts

Tablesaw lubrication

#1

Tablesaw lubrication

Kevin Mac Luskie

>I bought a used Powermatic 66 a while ago, and although I haven't used it a lot up till now, I'm getting ready to start doing a lot of work with it. I was going over it, cleaning it up and checking adjustment on it, and the height and angle adjustments are harder to turn than I think they should be. I checked to make sure the locking screws were not tightened, and used an air compressor really well on the worm gears to blow out all the current sawdust. In the book it just says:

"If binding occurs, clean off all sawdust and pitch buildup and re-lubricate with a good nonhardening grease."

Does anyone have a recommendation on what kind of "nonhardening grease" to use? will regular axel grease work, or the blue marine grease I use in the buddy bearings of my jetski trailer? Is there something that attracts less saw dust?

Thanks for you help.

-Kevin

Re: Tablesaw lubrication

#2

Re: Tablesaw lubrication

Neal in San Jose

>I've had very good luck using bicycle chain lubrication. Reasonably priced and easily available. The particular brand I have in my shop now is "White Lightening", and it is a teflon material in a very light carrier. The carrier (smells like alcohol) evaporates, leaving only a fine coating of solids that do a good job of reducing friction. Anything that stays liquid like axel grease or light machine oil will do a fine job of collecting sawdust and gumming up the works.

Re: Tablesaw lubrication

#3

Re: Tablesaw lubrication

Howard Acheson

>Many pros and writers of books on tablesaws use paste wax on the heli gears. Just a plain old furniture paste wax like Johnson or Minwax works fine. Apply it with a tooth brush and work the cranks to get to the whole gear surface. The wax will clean out any old gunk and sawdust doesn't stick to wax. Wax is an excellent low speed lubricant.

A drop of 20 weight electric motor oil on the bearings that support the crank shafts is all you need. On most saws the arbor bearings are sealed and you should not lubricate them unless you instruction manual recommends it.

Re: Tablesaw lubrication

#4

From a FWW article on the subject 

Dan MItchell

>


img

Re: Tablesaw lubrication

#5

one recommendation

Bill Tindall, E.TN

>I took a class from Delta years ago and the instructor lubed the slow moving parts with Johnson's paste wax.

Re: Tablesaw lubrication

#6

If you call Powermatic...

Scott in Montana

>...they will tell you to use white lithium grease. I didn't like it. I've tried Slip-it, Boe-Shield, and a couple others. I think it's tough to beat Johnson's paste wax.

Just one Powermatic 66 owner's opinion.

Scott

Re: Tablesaw lubrication

#7

I use a product call slip plate ---

Wayne Carson

>The one I use is made by John Deer it is a very heavy dry graphite spray that makes things work like it has ball bearings but is dry.

Re: Tablesaw lubrication

#8

Re: I use a product call slip plate ---

Rob Stokes in North Vancouver

>I use graphite (spray can) as well.

Rob

Re: Tablesaw lubrication

#9

Ellis Walentine

Who sells it, Dan?

Ellis Walentine

>

Re: Tablesaw lubrication

#10

Not Dan unless *LINK*

Dustmaker Mike

>you owe me money then I could be Dan(-; Here is the MFG Website. I use this stuff a lot around the house and cars. They have a link to find a dealer so you can find one close to you.


LPS

Re: Tablesaw lubrication

#11

Re: Free Tablesaw lubrication *LINK*

pecker

>Dow has samples available of a molycote type product. The one they sent me was a full size can. Probably last a lifetime.

http://www.dowcorning.com/applications/search/products/Details.aspx?prod=02412241&type=PROD


molycote 321

Re: Tablesaw lubrication

#12

Re: Tablesaw lubrication

Kevin Mac Luskie

>Thanks so much for all of the recommendations! Great info.

Since I've got Johnsons paste wax on hand for keeping my top smooth and slick, I'll give that a try to start with. But I've printed out the list of other recommendations for future reference.

Thanks again all!

Re: Tablesaw lubrication

#13

Re: Who sells it, Dan?

Dan MItchell

>Haven't needed it yet myself, my saw's too new, but the author's case that a dry lubricant attracts/holds less dust makes sense to me.

Dan

Re: Tablesaw lubrication

#14

Cheap at twice the price!

Dan MItchell

>I'm on this one, thanks for the tip!

Dan