Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Tambourette Table, Part III - Finished, (Pics) *LINK*

Posts

Tambourette Table, Part III - Finished, (Pics) *LINK*

#1

Tambourette Table, Part III - Finished, (Pics) *LINK*

Jim Shaver Oakville, Ontario

>Hi All,

Well I am done, the table is now finished. I last posted the update of the fitting of the parts and dry assembly, see the link below.

This post is about the glue up and finishing of the table.

Photobucket

The glue up process was very simple, the rabbet joint down the centre easily glued, I did pin it with two brads, one at the top, one at the base.

I followed a finishing process found on Jeff Jewitt�s web site for a Mission dye- glazed finish

http://www.homesteadfinishing.com/htdocs/articles.htm

Photobucket

I used Trans-tint medium brown for the colour, mixed with water and applied carefully by hand , keeping a wet edge moving across the work.

Photobucket

I then used a single coat of General Sealcoat to seal the dyed surface.

The next step was to apply a gel stain that would be the glaze over the seal coat, highlighting the texture and grain in the white oak.

Photobucket

Finally I applied 3 satin clear coats, scuff sanded between coats (320 grit) and then waxed.

Here is the finished table.

Photobucket

Photobucket

Photobucket

The finished work has a 16� diameter top and stands 26� tall. This makes a great lamp stand or a display stand.

Tomorrow I will taking this table to a friend as a gift, she underwent breast cancer surgery this week and starts radiation Monday. She is fine but it�s been a difficult few weeks.

I enjoyed this simple project, I learnt a few things along the way that I would say were well worth the effort. I also hope you have enjoyed my documented process and found it helpful in understanding somethings you may not have known about before.

Take care,

Jim


Part II

Re: Tambourette Table, Part III - Finished, (Pics) *LINK*

#2

Re: Tambourette Table, Part III - Finished, (Pics)

George@Colonel's Workshop-Havertown PA

>Good Afternoon Jim,

It looks just like it should look. I am not down playing the effort, but celebrating its success. Congrats. I know the gift will be well received, and surely profoundly appreciated over time.

George

Re: Tambourette Table, Part III - Finished, (Pics) *LINK*

#3

Hi Jim, Maybe I'm daft, but...

Scott Burr in Ben Lomond, CA

>How's the top attached?

It turned out very nice. You did a great job!

Re: Tambourette Table, Part III - Finished, (Pics) *LINK*

#4

Figure 8's *LINK*

Jim Shaver Oakville, Ontario

>Hi,

I never made an image of the top fasteners, sorry. The top is attached to the top of each leg with a figure 8 connector. Hope that helps.

Take care,

Jim


img

Figure 8

Re: Tambourette Table, Part III - Finished, (Pics) *LINK*

#5

Re: Tambourette Table, Part III - Finished, (Pics)

Clint Searl, at the base of Haycock Mtn

>You do good work, Jim. That is one handsome table.

Clint

Re: Tambourette Table, Part III - Finished, (Pics) *LINK*

#6

Got it, thanks!

Scott Burr in Ben Lomond, CA

>

Re: Tambourette Table, Part III - Finished, (Pics) *LINK*

#7

Paul Kramer

WOW! Very nice work -- For a great cause

Paul Kramer

>

Re: Tambourette Table, Part III - Finished, (Pics) *LINK*

#8

Ellis Walentine

Thanks, Jim. Nice job, as usual.

Ellis Walentine

>Of all the recipes for a mission oak finish, I've always felt that Jeff's approach is the most accessible, and it looks great. Thanks for showcasing it here and for your excellent workmanship.

Ellis