Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Rosewood Finish

Posts

Rosewood Finish

#1

Rosewood Finish

Bill Pfahl in Virginia

>I am presently finishing a Rosewood top table. Had it sanded today and found that the wood is extreemly oily - well duhh. When I got the top home I found that the ends are starting to split. This is a MAJOR problem. Originally I had planned to use Spar Urethane as the finish. But now am wondering if that is a good idea with this oily wood. Jon Arno, are you out there? Any recomendations would be greatly appreciated, also how to remedy the splitting (shorting the top is not an option). Thanks in advance, Bill.

Re: Rosewood Finish

#2

2 Questions

Mark Mandell - Gone Round In Jersey

>The way to prevent the split is to use dry wood |;-}}}}

If the wood is "dry" than you're likely changing its enviorment too quickly. You can control the splits by using them as a design elements and locking them with butterfly inserts. Once the flies are in place, file the checks with epoxy and sand smooth.

Finishing on troipical like rose should be preceded with a wash and dry with acetone or naptha to leach out and wash away the surface oil film. You can then proceed with your finish. You might consider a sealer coat of dewaxed shellac to prevent further oil seepage asndf build depth.

I've done rosewood with oil poly as well as lacquer with excellant results. Why, may I ask, are you planning "spar" varnish? Is this piece going outside or on a boat? Spar is usually used in weathering situations; not necessary for interior use, and probably not the best use inside as it tends to be a softer, more flexible finish.

mm

Re: Rosewood Finish

#3

Re: 2 Questions

Dan Donaldson

>I have had problems with poly finishes drying on Rosewood. At first, I thought to just wait, but it never did harden. If you want to use poly, I would recommend that you use some shellac to seal it first.

Re: Rosewood Finish

#4

Re: Rosewood Finish

Clint Searl, at the base of Haycock Mtn

>Our dining table top is solid cocobolo that I made around 1985. The finish is auto clear coat acrylic lacquer, preceded by an acetone wash. No problem to date.

I don't know about true rosewood, but cocobolo will check slightly as it ages

Clint

Re: Rosewood Finish

#5

Re: Rosewood Finish

Fred Davis

>Assuming this is real Rosewood and a good thickness for tables, I wonder how you scored that. Kinda like collecting enough Passenger Pigeon feathers for a pillow.

FredD

Re: Rosewood Finish

#6

Clint......True Rosewood

HC Sakman

>Hi Clint,

Cocobolo is a true rosewood. Botanic name is "Dalbergia retusa".

Just FYI.

Chico...

Re: Rosewood Finish

#7

Re: Rosewood Finish

Bill Pfahl in Virginia

>Thanks guys for the responces. The table is a re-build originally made in the 1960's, three boards wide. I resawed, reglued it with full length splines. The base is curly Maple legs and stretchers, attached with threaded inserts. I usually use naptha as a wash before appling finish. I'll investigate shellac and acrylic lacquer -then all I heve to do is sell it to the owner. I'll post a picture when finished. Thanks again guys, your a life saver. Bill.

Re: Rosewood Finish

#8

Re: Rosewood

Mark Mandell - Gone Round In Jersey

>I have several planks of Brazilian Rosewood which I made into a table 40 years ago. Table's gone but I salvaged the planks. What are they worth today at 1x12x96? |;-}}}

Re: Rosewood Finish

#9

Re: Rosewood

Bill Pfahl in Virginia

>Mark, Last I heard Rosewood was going for $27. a board foot.

Re: Rosewood Finish

#10

Ellis Walentine

Value depends...

Ellis Walentine

>If it is really nice looking wood, with no pinholes or knots, a musical instrument maker could get about 12 sets of guitar sides and backs out of each of your boards. Brazilian rosewood guitar sets, if you can prove they are pre-embargo wood, would fetch upwards of $250 per set, possibly much more.

Old Brazilian rosewood can be pretty nondescript looking because the bright colors turn darker and muddy with age and oxidation. You'd still be looking at a pretty hefty value.

BTW, have you ever picked up a Brazilian rosewood board and tapped it with a small hammer, or even a fingertip? It rings like a bell.

Ellis

Re: Rosewood Finish

#11

Re: Value depends...

Dan Donaldson

>The ringing is really neat. They make the tone bars for a marimba out of rosewood and the tone they get on the good ones is amazing.

Re: Rosewood Finish

#12

Hmmmmmmm

Mark Mandell - Gone Round In Jersey

>Bought the wood from Jake Brubaker out in Landisville, PA (along with a carved billet-form that hangs over my fireplace). Jake and the receipt, if any, are both long gone after 40 years.