Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

My Limbert Tabourette, A Work In Progress Part II *LINK*

Posts

My Limbert Tabourette, A Work In Progress Part II *LINK*

#1

My Limbert Tabourette, A Work In Progress Part II *LINK*

Jim Shaver - Oakville, Ont

>Hi All,

Well here is Part II on my Limbert Tambourette table. This is a fun project and I enjoying documentation my process for you to red.

Last we spoke the table was in a roughed out condition, the legs were laid out and cut at the bandsaw and the top was cut as well.

My next step was to use a pattern bit at the router table and use the leg template to route out 4 identical legs.

Photobucket

It had been awhile since I have used my router table, a few moments spent visualizing the cuts and the direction of feed vs. potential grain conflicts and off I went. I had rouged out the size to the template on the generous side of extra wood, so I used progressing sized bearings to make the cuts till I was comfortable to go to the net bearing size for the final cut.

Quite a difference from the roughed out look, the routed shapes have a final look. Despite the routed sizing being close to final I still used some rasps and spoke shave work to get the ready to finish surfaces I wanted.

Once I had the legs dry fitted I was able to now measure up for the slot cuts on the lower shelf.

Photobucket

I used a table saw set up to get centered slots and some fret saw cuts and final chisel work cleaned it up nicely.

I sized my shelf stock thickness a hair more that the slot in the legs, so for a clean crisp fit I planed down the over all shelf thickness till I got that custom fit.

Photobucket

I used a small can of wax to lay our the corner radius and cut them clean at the band saw, some final rasp work and a quick light sanding and they were done.

Photobucket

So here it is, all dry fit, all hand planed and ready for glue up then a finish

Photobucket

Photobucket

Photobucket

Everything is coming together well, I have a few things I would do differently next time at the router table, but I have been flying through this project quickly.

Stay tuned, I have a feeling it will be ready really soon for final presentation,

Take care,

Jim


Previous Post, Part I

Re: My Limbert Tabourette, A Work In Progress Part II *LINK*

#2

Looking pretty!

Clint Searl, at the base of Haycock Mtn

>

Re: My Limbert Tabourette, A Work In Progress Part II *LINK*

#3

Paul Kramer

Jim, Thanks for showing. Lovely piece so far

Paul Kramer

>

Re: My Limbert Tabourette, A Work In Progress Part II *LINK*

#4

Re: My Limbert Tabourette, A Work In Progress Part

David Yoho

>I love watching you work, Jim. Looks great as always. You gotta love QS white oak. It sure is pretty!

David

Re: My Limbert Tabourette, A Work In Progress Part II *LINK*

#5

Where's your helper?

Lee Schierer - McKean, PA

>Your helper seems to be missing from this series of photos. The table is looking good so far!

Lee

Re: My Limbert Tabourette, A Work In Progress Part II *LINK*

#6

Re: My Limbert Tabourette, A Work In Progress Part

George@Colonel's Workshop-Havertown PA

>Good Afternoon Jim,

You made great and careful progress, as the dry fit shows. The table's proportions are especially pleasing. Can't wait until you post pix of the finished item.

George

Re: My Limbert Tabourette, A Work In Progress Part II *LINK*

#7

JL

Re: Thanks for posting..

JL

>Darn, another to put on the to do list :).

Re: My Limbert Tabourette, A Work In Progress Part II *LINK*

#8

Will you look at that?!

Joanne Adler in Pt. Pleasant, PA

>A saw powered by a bicycle in the background! Is THAT why General makes their tools "green"? :-)

Seriously, dude--you need to move! You need a bigger shop! The rest of your life's stuff is getting in the way of sharp tools. That's why I finally had to move--no more room in the garage.

I like the understated gloat on the Sauer plane and Japanese slick. And for not having used the router table in a while, you did a great job on the template routing. The legs look perfect.

But the table is fantastic! Gorgeous oak. I can almost smell it from here in PA. Love that smell. It is going to look wonderful finished and next to the Morris Chair. Actually, it would look good anywhere. Including MY living room, MY kitchen, MY hallway . . . should you ever tire of it. ;-)

As always, a wonderful write-up. Thanks for sharing, Jim.

Re: My Limbert Tabourette, A Work In Progress Part II *LINK*

#9

Re: Will you look at that?!

Jim Shaver Oakville, Ontario

>Thanks Joanne,

So you saw the S&S and the Imai...very sharp....eyes!! LOL

Yeah, my space is cramped top say the least, some things will change I know in time...but for now it's all wood, every square cm of that shop...I have to consume some more wood, my next project will drop my inventory by about 200bd ft....:-)

Bicycles, what bicycles?? I Don't see any bicycles in there....?!?!?

:-)

Take care,

Jim

Re: My Limbert Tabourette, A Work In Progress Part II *LINK*

#10

Re: Where's your helper?

Jim Shaver Oakville, Ontario

>Thanks Lee,

Dana is away at a friends cottage this week, it's been really strange not having her around.....sigh.

Take care,

Jim

Re: My Limbert Tabourette, A Work In Progress Part II *LINK*

#11

Re: My Limbert Tabourette, A Work In Progress Part

Jim Shaver Oakville, Ontario

>I always enjoy your work as well David

Thanks,

Take care,

Jim