Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Lee Valley digital angle finder

Posts

Lee Valley digital angle finder

#1

Lee Valley digital angle finder

Dan Mitchell

>I just received one of those $20 Lee Valley digital angle finders. Seems to work OK, but the instructions indicate it should invert the display when you turn the unit over, so the readout is always right side up. Mine does not do this; turn it over, the display is upside down. Anyone else notice this, or am I doing something wrong?

TIA

Dan

Re: Lee Valley digital angle finder

#2

Re: Lee Valley digital angle finder

North of the Border

>I think the "it' in the Features section: "Display always reads upright, no matter which way it is turned" refers to the moving blade (i.e. the arm with the square window opening), not the angle finder unit itself. No where in the leaflet could I find any diagram showing the unit upside down and the reading upright. May be like you, I miss something there.

Re: Lee Valley digital angle finder

#3

Re: Lee Valley digital angle finder

Dan Mitchell

>Thanks for the reply. So yours does not remain upright either?

If you look at the diagram at the bottom right hand corner of the front page of the instructions. The left hand image shows "45.0" upright with the control buttons below the readout, the right hand image shows "45.0" upright with the controls above the readout. Also, the image below from the Lee site seems to show the readout remaining upright as well.

Does anyone have one which remains upright? I also have a Beall gauge (yes, I'm a bit of an obsessive ;-) The display on it remains upright regardless of position.

Dan


img

Re: Lee Valley digital angle finder

#4

You're right.

North of the Border

>I'll be doing a small purchase at LV Monday and will check it out when I 'm there - if the puzzle isn't resolved at this forum over the weekend.

Re: Lee Valley digital angle finder

#5

Re: Lee Valley digital angle finder

Alan in Little Washington (NC)

>My display inverts (stays upright) when you flip the unit, just like the literature says.

Re: Lee Valley digital angle finder

#6

Re: Lee Valley digital angle finder

Dan Mitchell

>Thanks for the replies, interesting that at least some of them DO invert.

Naturally "I" have to get one that's HOSED! ;-)

Not a huge issue, but if it's supposed to, IT'S SUPPOSED TO! I look forward to hearing what they have to say at the store, I may email them as well.

I see there's a Lee store in Vancouver. We're in Seattle & go up to BC occasionally, have to check the store out there next time.

That is if I don't spend all my spare $$$ at the Grizzly store in Bellingham on the way up! ;-)

Dan

BTW, anyone have any experience with a Lee return? This is only my 2nd purchase from them. In particular, this being an apparent defect, I'd hope they'd pay return shipping.

Re: Lee Valley digital angle finder

#7

Re: Lee Valley digital angle finder

Harvey Brooks, Victoria, BC

>They will exchange it or refund your money and refund your shipping expense also. If it was shipped to you, there is return postage paid address label attached to your invoice that you can use to return it. Otherwise, they will send you a cheque to reimburse you for your shipping expense.

Harvey in Victoria - waiting for the new store to be built so I don't have to worry about shipping any more.

I was by the new store site today and the floor and pillars are poured, ready to have a roof installed.

Re: Lee Valley digital angle finder

#8

Re: Lee Valley digital angle finder

Howard Norman

>>BTW, anyone have any experience with a Lee return? This is only my 2nd purchase from them. In particular, this being an apparent defect, I'd hope they'd pay return shipping. <

Lee Valley is probable the easiest company that I know of to deal with on returns. Never had a problem with them on a return. Of course I must admit I haven't had many returns over the years.

Re: Lee Valley digital angle finder

#9

Re: Lee Valley digital angle finder

John Ballance

>I just received mine. Per the instructions, with the body horizontal and the pivot hinge on the right, raising the front swing arm is a positive angle, and the device presents a display that is upright. However, swinging the arm down below the body from this position (into the "minus region") causes the display to invert. This would give an upright display if the body was oriented with the hinge to the left. Mine works like that. But the display does not invert when I simply turn the device over -- I have to swing the front arm into the "minus" region to invert the display.

Try this on yours.

I hope this helps.

By the way, I will have to rethink my angles, since I learned that a positive angle was in the first quadrant (upper right), not the second quadrant (upper left) as this device appears to be defined.

John

Re: Lee Valley digital angle finder

#10

Any pix to demonstrate

North of the Border

>your explanations? I tried as you described it but couldn't get anything to 'invert.' A pic or two would help, if possible.

Re: Lee Valley digital angle finder

#11

Re: Lee Valley digital angle finder

Dan Mitchell

>John - Again mimicking the drawing in the instructions, I finally got mine to do invert the display, but only after pressing "Zero/ABS", button several times. This is odd, since one of the 1st things I did with the unit was zero it by placing it flat on one wing of my jointer & pressing "Zero/ABS", something which I did several times later as well while testing various machines in the shop. I'm sure there's some logic to this, but exactly what it is escapes me.

Thanks for your reply.

Dan

Re: Lee Valley digital angle finder

#12

Got it. Thanks

North of the Border

>The unit will read upright at all times only in ABS mode. That's what I missed, which isn't pointed out under the Features section but is explained in the Under "ABS" mode box. .

Re: Lee Valley digital angle finder

#13

Re: Got it. Thanks

Dan Mitchell

>I must have looked this one page instruction sheet over front-to-back 5 times or more, & I missed that little box. Whatever your stand on the "Chinese tool" question, I think everyone will agree they could write better documentation.

That's my excuse and I'm STICKING WITH IT! ;-)

Re: Lee Valley digital angle finder

#14

Jointly responsible ,,,,

North of the Border

>I actually hold the sellers (e.g. in this case LV) jointly responsible for the quality of the instructions / manuals because they are the ones which will have to deal with the customers' or endusers' inquiries and questions. I do think there's a niche market here for those woodworking retailers which are willing to spend the resources on improving the documentation for their Asia-imported goods as part of their services. Many China- or Taiwan-made woodworking tools are not bad in their quality (given their prices - comparing apples to apples), but the same can't be said of their manuals or guides. I strongly think before any of the importers sell their tools in N.A., they should read the instructions themselves and see how easy or different for themselves to follow. If they aren't happy about what's there, they should improve on it before dumping it onto their customers.