Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Load Limit of my Lumber Rack? *LINK*

Posts

Load Limit of my Lumber Rack? *LINK*

#1

Load Limit of my Lumber Rack? *LINK*

Brian in Sandusky, OH

>See attached pic, and also a detail shot in a second message.

The joists are 2x8's, at 2' spacing.

The rack is made from 2x4's with two 3/8" carriage bolts attaching to the joist, and one attaching to the bottom strut.

The racks are attached at 4 spots on the four last trusses.

First off, I will say that I don't think that I have plans to completely fill it with lumber. I'm not positive that it will hold a full load.

And when I do start to fill it, I will fill it outward in...there's certainly more strength at the outer edges of the trusses where the walls can take up some of the load.

What do you think? Could I completely fill this rack without my shop falling down? :)

If you want to see complete progress shots of my shop from beginning to where I am now, see the link below.


img

Complete Progress Shots

Re: Load Limit of my Lumber Rack? *LINK*

#2

Load Limit of my Lumber Rack? Pic #2 

Brian in Sandusky, OH

>


img

Re: Load Limit of my Lumber Rack? *LINK*

#3

Re: Load Limit of my Lumber Rack?

Kneale Brownson Dreaming of the Snow in N. MI

>You're using spliced 2X8 joists to support both a floor above and your hanging racks? I wouldn't load 'em up with anything heavy.

My 28-foot-wide barn has a 14-inch high steel I beam down the center and 2X12X14 full-sized (rough sawn) floor joists 16 on center.

Re: Load Limit of my Lumber Rack? *LINK*

#4

They will hold quite alot for sure......

Scott in Eastern Iowa

>....but I wouldn't fill those cavities 100%.

Theres a few structural guys around here (Ray Carson in Jersey for one) who could tell you pert near what it would hold, but those are deep spaces that could hold over a ton of wood Im guessing, but may bend/ deflect/ snap that trusses bottom chord if point loaded too much. I wouldnt chnace it....especially if the wood is fresh waterlogged green wood.

Now, take a single 16' section of a Louisville extension ladder, cut it in half ( 2 8' pieces) and bolt it horizontally like you have done here and I will tell you that filling all those spaces 100% will hold wood for 7+ yrs !!!

Re: Load Limit of my Lumber Rack? *LINK*

#5

Re: Load Limit of my Lumber Rack?

Fred Davis

>Gee Brian ,

your a brave soul.

Regarding whether the racks you put up will hold a load , any load , all of which is dead weight , the worst type of load ,it looks like you already have decided to use your ceiling joists for lumber racks which at 24 " o.c. are already over span.

If you don't park anything valuable underneath , you can look forward to seeing the joists fail at their weakest point which is the gang nail.

I don'nt see any sign of the truss which you refer to, nor any bottom chord, so lots of luck.

I understand from reading Scientific American that the pull of gravity varies from place to place,maybe yours is one of those places.

FredD

Re: Load Limit of my Lumber Rack? *LINK*

#6

Sort of long response

richard jones

>B,

I will hazard a fairly educated guess and say that IF you fill that space completely you will certainly be creating an overstressed situation. If you have access to the specs on the trusses or know where they came from, see if you can find out the design load. Doubtful it is going to be more than 40psf live load, so you can do the math there. It is possible to design a truss to bear your imposed loading, but I would think it would be far larger than a 2x8 bottom chord, maybe even some LVL members. I have seen some very large room trusses for ROG's with bottom chords composed of 4-ply 11 7/8" LVL's that I'm glad I don't have to lift.....:)

That said, I quite often see drywall stacked in ROG's such as yours and that has pretty good weight, and would incur more of a concentrated load stress than your rack would. Of course, the closer you keep the load to the outside walls, the less stress you place upon the assembly (imagine a see-saw with more and more people on one end. Move the people closer to the fulcrum and you don't stress the load end of the see-saw board as much. There are compromises with everything).

I've never seen a properly applied gang nail fail, altho' I've seen folks saw them in half and expect them to still do the work of the original size........:)

Track the deflection by measuring from some points on your garage floor and marking them permanently on both the floor and the bottom of the truss so that you can re-create the exact vertical line from which you originally measured. Or, use a string stretched from top plate to top plate. If you start to get quite a bit of deflection, say, more than L/360, then you may want to reconsider. Here's an excerpt from the American Wood Council, but keep in mind, this is for nominal lumber, not trusses, but does give you a good starting point: "Maximum deflection limits are set by building codes. They are expressed as a fraction; clear span in inches (L) over a given number. For example: a floor joist appropriately selected to span 10 feet with an L/360 limit will deflect no more than 120"/360 = 1/3 inches under maximum design loads. Drywall attached to the underside of this system is not expected to crack when the floor joist system deflects 1/3"." The truss specs should also include the deflection limits.

As far as catastrophic failure, unless you load the entire thing in one day, you will more likely see a gradual deflection in the bottom chord. Eventually, it could fail entirely.

Remember, you can go out and buy another car, but it took you a long time to fit those quartersawn runners on your TS sled.........:)

Rich (whew!) in VA

Re: Load Limit of my Lumber Rack? *LINK*

#7

Gravity

Mark Goodall - ATL - tooljunkie

>I hang lightweight stuff, leftover molding, PVC pipe, sanding belts, paint brushes, etc from the ceiling. But my stash of lumber, mostly oak, maple and walnut, are all on steel shelves that rest on the ground or attach directly to studs that rest on the ground.

Happy Woodworking!

Re: Load Limit of my Lumber Rack? *LINK*

#8

Brian, I can help you... cut the stress by 2/3

Joe in a Cleveland suburb

>I would say buy rough lumber (should probably only be Cherry and Walnut)with the intent to fill those spaces completely.

Now, in an attempt to help an Ohio neighbor, for every 3 boards you buy, you give me 2. This way you will only have 1/3 the weight there that you thought you would have.

Smart thinking on my part, eh? Just trying to help.

Joe

Sorry, I'm no help. I'll leave now...

Re: Load Limit of my Lumber Rack? *LINK*

#9

Re: Load Limit of my Lumber Rack? Pic #2

Pete in Holland, MI

>Although I like the design, the possibility of bringing down the garage is real if you fill the racks.

You should be able to go to a decent lumber store that caters to contractors (not Lowes & Home Depot). They should be able to give you a load capacity of the 2x's that you are attached to, or a load per square foot of a floor system.

Besides, if you have 2' of lumber in these racks, it'll be a real pain trying to get to the boards on the bottom, especially if you're on a ladder. Might want to sub-divide the racks into 2-3 shallower cells to aid future access to your lumber.

Re: Load Limit of my Lumber Rack? *LINK*

#10

Re: Load Limit of my Lumber Rack?

Brian Gray in Sandusky, OH

>Thanks for all the feedback, everyone.

I think that the plan is to fill it no more than 1/3, and use the rest of the space for lighter stuff.

And Joe, you can come up for lumber anytime!