Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Success, Table saw aligned.

Posts

Success, Table saw aligned.

#1

Success, Table saw aligned.

jeff

>Hi all

Thank you for all the help.

I spent the better part of the day aligning the table saw.

First got the table and blade perfect at 90, then aligned the 45 cut.

I'm .0005 (1/2 a thou) on 90, and .002 (2 thou) on the 45.

Alot more fiddling then I thought it would take, but it's done.

Of course, everything had to be taken apart and put back together, and the fence, stops, plates all needed to be readjusted.

But, now the 45 cuts are perfect, no more concave.

Next project is to re-cut all the box parts and get them glued up.

Jeff

Re: Success, Table saw aligned.

#2

Re: Success, Table saw aligned.

George@Colonel's Workshop-Havertown PA

>Good Afternoon Jeff,

I followed the thread with interest, not having any good idea of what the cause of the problem was. I hadn't run up against a similar condition. I don't envy you the alignment job, and am glad its over to your satisfaction. I used my Beall Tilt Box to tune my SCMS today as a part of a shop down/clean up time. Alas, the saw was dead on to start with, and the new Tilt Box is back sleeping.

George

Re: Success, Table saw aligned.

#3

Angle Finder makes angle cuts perfect

North of the Border

>I agree - a digital angle finder like the Beall Tilt Box goes a long way towards making accurate cuts. Mine is a much cheaper version from LV ($19.99) but it works great. Look at the picture showing the 22.5 degree bevel rips I made using the angle finder to set the blade (I'm making octagon lotion dispensers). The joints are as tight as they can be; I was amazed by the result. My cheap Delta tablesaw has since performed so much better ....


img

Re: Success, Table saw aligned.

#4

Re: Angle Finder makes angle cuts perfect

jeff

>Nice joints.

I don't mind spending time getting a perfect cut or joint.

But I hate when I'm working along, get set up for a cut, thinking things are all set, and bang, everything goes wrong.

When I did a run of boxes, I noticed a small gap in one and figured it was just me.

This last batch really threw me for a loop, all the cuts were bad.

I usually figure the problem is me, so I'll build a jig to be sure the cuts will be dead on. I try to eliminate all the human error I can (I'm usually the error!) since I know better.

Jeff

Re: Success, Table saw aligned.

#5

Re: Success, Table saw aligned.

jeff

>George

I really didn't have a clue to the problem at first.

If it weren't for this forum and the answers, I wouldn't have had a clue that the angle changed.

I built 3 jigs, just to prevent problems with these cuts.

I am rebuilding one jig that has some error in it I found when trouble shooting the cuts.

I also built a special jig just to do one test while trouble shooting.

I wish I could figure a way to do the 45 cuts without even tilting the blade to keep things perfect.

But, alas, all I've tried haven't really worked well.

But, I'll keep looking.

I thought about a tilt guage, but the ones I'm using are spot on and I can't see it helping all that much going digital.

Jeff

Re: Success, Table saw aligned.

#6

Going digital?

North of the Border

>"I thought about a tilt gauge, but the ones I'm using are spot on and I can't see it helping all that much going digital."

I think the price of $19.95 (LV's angle finder) is worth a try in your case. I used to set my tablesaw at 90 degree using a tri-square which I was told should give a dead-on 90 degree setting and a combination square for a 45 degree setting. Since I got my digital angle finder, I'm convinced whoever told me about the tri-square etc. was only half-correct: those measuring tools are good but not as good as a digital one. They can't match the digital accuracy and the clarity of the reading.

Re: Success, Table saw aligned.

#7

Re: Success, Table saw aligned.

Jim Dillon

>Jeff,

"I wish I could figure a way to do the 45 cuts without even tilting the blade to keep things perfect."

Yeung Chan's book describes a jig for cutting miters for boxes etc. without adjusting your TS blade from vertical. I built it and it works fine, although one is limited in the length of board one can use.

Jim

Re: Success, Table saw aligned.

#8

Book Name?

jeff

>

Re: Success, Table saw aligned.

#9

Cancel that, I have it.

jeff

>

Re: Success, Table saw aligned.

#10

Re: Book Name?

Jim Dillon

>Jeff,

"Classic Joints with Power Tools" by Yeung Chan, Lark Books, 2002. IMHO it is a superb book. Here, hopefully, is a pic of the jig I previously mentioned.

Jim


img