Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Clock Progress Report

Posts

Clock Progress Report

#1

Clock Progress Report

George@Colonel's Workshop-Havertown PA

>Good Afternoon Friends,

The grandmother clock which Charlie and I are making is really coming together. Last Saturday we made significant progress, successfully installing the door hinges and magnetic catches, and mounting the doors to waist and bonnet, precisely re-positioning the ferrels to the bonnet columns, and installing the face board. We also mounted escutcheon hardware and finials to get some idea of the final outcome. We decided while building the bonnet, to push back the face board significantly to insure the suspended weights adequately cleared the transition molding between the waist and base. The weights drive the clock, and the effective length of the attaching chains determine the frequency of winding. When we pushed back the face board position, we were able to "box" in the sides and extend the arched top of the enclosure. It was an unplanned and totally successful design change. It brings more drama to the face's appearance.

George

George


img

Re: Clock Progress Report

#2

Re: Clock Progress Report- continued

George@Colonel's Workshop-Havertown PA

>Good Afternoon Friends,

This is how the clock looks without the application of color and finish. The waist door is partially inset which required some mortise work at the hinges. Charlie and I did that with a laminate trimmer and various hand chisels. We used a rare earth magnet from Lee Valley to secure the waist door, which is 1/4" rabbetted to a piston fit. The door is one solid piece of 3/4" cherry, 11" wide by approx 28" long. The edge profile was done on my router table and completed with Charlie's chisel work. The door is totally flat. Overall, the clock will be about 11 1/4" wide at the bonnet and 80" tall with finials mounted. We had some very slight warpage in the face door frame which required extra care and time installing the hinges properly. In the end, we were able to mount the face door perfectly, and did not have to relieve either the door or surrounding cabinet/arch for opening clearance. (We had some luck there!) Overall inspiration for the clock came from a Grandfather's clock in the Governor's Mansion at Williamsburg, VA. As the project developed, we modified the design as we went along, first shrinking it in height from the original, then putting a new "width" on each component, and finally coming up with a totally different looking bonnet. We are in the midst of deciding what the ultimate finish will be. Our next step will be to locate and mount a dummy movement. Once that is done, we can disassemble the clock for final sanding and feathering.

George


img

Re: Clock Progress Report

#3

Re: The Three Grandmothers

George@Colonel's Workshop-Havertown PA

>Good Afternoon Friends,

At least two of the three grandmothers pictured approve of our progress. My wife Kathy is on the left, Charlie's wife Claire is on the right. The grandmother in the middle is as yet unnamed.

George


img

Re: Clock Progress Report

#4

Time, Tide and departing ships

Lee Schierer - McKean, PA

>Looks like your timing is good. It looks like the movement went in without too much persuasion. How did the trimming of the brass corbell work out?

Lee

Re: Clock Progress Report

#5

Re: Clock Progress Report

Thomas Skaggs, Foothills of Mount Level

>Colonel,

I must hand it to you you, on face value I'll chime in and say that my critique pendulum is swinging towards ringing success!

Tom

Re: Clock Progress Report

#6

Great post

Bill Tindall, E.TN

>Enjoyed the read.

You guys work too fast. I fee like a laggard at the progress I am making.

Re: Clock Progress Report

#7

Re: Time, Tide and departing ships

George@Colonel's Workshop-Havertown PA

>Good Afternoon Lee,

We ended up trimming three of them on the sanding disc, and they fit perfectly after some fussing. We also repositioned a couple at the bottom of the columns. We installed new pins at the rear side of each casting to anchor in place. As you observed, we had plenty of brass to work with.

George

Re: Clock Progress Report

#8

Alan Young

So are the rolling pins held by the Grandmothers'

Alan Young

>hid behind the clock?

Great project George!

Alan

Re: Clock Progress Report

#9

JL

Re: Clock Progress Report- continued

JL

>Thanks for the update. Speaking from ignorance, having never built a clock before.... why a dummy movement?

Re: Clock Progress Report

#10

Re: Clock Progress Report- continued

George@Colonel's Workshop-Havertown PA

>Good Evening JL,

The dummy movement is Charlie's idea. He built one with identical dimensions to the Hermle we will ultimately install. It won't matter if we drop it, shim it, twist it, hammer it into submission/precisde location. Once done, we will be able to install the real one without any risk of damage, having determined the precise thickness/length, clearance of bridging and support pieces and chime bar/sounding board. It will save us time and risk. When we installed the movement to my wife's clock (Shop

Shot #769 )it took us a couple days of fussing to get it perfect.

George

Re: Clock Progress Report

#11

Now just a Minute

Joanne Adler in Pt. Pleasant, PA

>I want to Second Tommy's kudos! I love tall clocks and I am so TICKled that you're making one. And having such a great Time while doing the construction. Bravo!

Re: Clock Progress Report

#12

JL

Re: Thanks, makes good sense

JL

>