Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

On making a curved top

Posts

On making a curved top

#1

On making a curved top

Bill Tindall, E.TN

>For this top I am following directions as provided by Will Neptune in a demo last year at the fall SAPFM meeting. The first step is to prepare the staves for the top. 1. Determine the circumference of the circle the curved top is derived from, 120 inches in this example. (the formula circumference = 3.14 times the radius may be handy for this step) 2. Select a stave width, in this example 3". 3. Determine the angle to saw or plane the stave edges. This angle is calculated as follows: Circumference divided by stave width- 120/3 = 40 staves to complete the circle of 360 degrees. 360 degrees divided by 40 staves = 9 degrees per stave. But this angle is shared by adjacent staves so the angle on each edge is 6 /2 = 4.5 degrees. So the saw is set at 4.5 degrees to angle the stave edge. 4. Each stave is sawed 3" wide with a 4.5 degree angle on each edge.

Now the clever part. If these staves are glued up in this state there will be a lot of shaping to make the top round inside and out. 5. Leave the saw set at 4.5 degrees and turning the stave on edge saw off the top of each stave to a distance of 1/4 the width of the stave as noted in the picture by "X". This wood would otherwise have to be removed after the top is glued up. 6. Mark the radius of the top on the bottom of the stave as shown exaggerated in the picture. Using an operation like what is used to make a cove on the table saw saw, saw away the bottom of the stave just up to the curve mark. Again, this wood would otherwise have to be removed after the top is glued up.

The bottom line for the stave is as follows- the edges are angled, the top is beveled and the bottom is curved as shown in the picture.


img

Re: On making a curved top

#2

Assembling the top

Bill Tindall, E.TN

>A clamping jig is prepared as show in the picture. For glue to work it must wet adjacent surfaces during assembly. Furniture factories only apply glue to one edge, but they get parts assembled quickly before there is any chance for the glue surface to begin to dry. Glue is cheap and I can deal with the mess, so to be sure each edge is wet I apply a ribbon of glue to both edges. I want to see squeeze out to be sure the joint is as good as it can be.

I was amazed how secure this jig held the parts. There was no tendency for the parts to skid out of alignment. I made the jig by stacking the 4 parts and sawing them as one unit to be sure they all lined up perfect.


img

Re: On making a curved top

#3

That looks good Bill,

Keith Newton, LR, Arkansas------WebKitFormBoundary

>That kind of clamping jig is the way to go. But there are a few things I might have done differently.

The cutting of the angles can be replaced with the strip canoe method of cutting a flute on one edge, and a matching half-round on the other edge. This offers a self-alignment benefit without having to hit that bevel angle/ width perfectly. It also allows the freedom to have a changing curve, without having to get complicated angle / width calculations.

I normally like to use yellow glue for edge gluing, however for this I would have used epoxy, thickened with colloidal silica.

Re: On making a curved top

#4

Circumference = pi x d

JohnM in Mid Mich

>Ummm... just for the record, circumference is 3.14 x d, or 3.14 x 2r, not 3.14 x r.

Re: On making a curved top

#5

Oooops Never post math when you are distracted.

Bill Tindall, E.TN

>