Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Band saw speed

Posts

Band saw speed

#1

Band saw speed

Bill Houghton, Sebastopol, CA

>My son's got an older 12" Craftsman bandsaw that he's setting up for use, and he's wondering about blade speed. My references are confusing: one (1950s) says 2050 feet per minute (fpm), while a recent Sears catalog lists saws ranging from 2400 to 3000 fpm, and my ten-year-old Delta catalog lists woodcutting bandsaws at 3000 fpm.

Is there a standard? And, for an older, cast-aluminum-bodied saw, is slower bad?

Re: Band saw speed

#2

Re: Band saw speed

Paul Woolson

>This is mostly just speculation, but I don't see how there can be a standard. Assuming they all use a 1750 rpm motor, if the blade length was different the fpm would be different. I don't think there's any way they change the speed of the motor for every blade size out there.

Re: Band saw speed

#3

Re: Band saw speed

Mitch from Canada

>I have a 25th anniversary Sears bandsaw that is now about 20 years old. We bought it new. From the manual I have for it and my memory (can't get to the manual right now), there are two different speeds for that bandsaw. I've always had mine on the higher speed (approx 3000rpm). From what I read, a higher speed for a bandsaw is better to work with. Hope this helps.

Mitch

Re: Band saw speed

#4

Don't worry too much about it

wilbur

>The range of useable speeds on a bandsaw for wood cutting is so wide that it really doesn't matter much. I have an old Walker-Turner bandsaw, and when I bought it, the pulley setup was such that the blade speed was about 2000 fpm. Looking at old catalogues, the fpm specified was 2500-2900 fpm, depending if you had the 14" or 16" bandsaw. When I did my mini refurbishing of my bandsaw (still in progress), I replaced the pulleys so that I had about 3200 fpm.

For metal, that's a different matter.

Re: Band saw speed

#5

Re: Band saw speed

Larry Clinton At Frankfort (Central)., Indiana

>Yes they can Paul. As far as I know there are no "direct drive" saws made. Therefore all they have to do to change speeds is to alter the diameter of either the drive or driven pulley (or both). My old Crapsman bandsaw (tilt head style) had a stepped pulley system for Hi/Lo speeds. The speed the factory specifies is directly related to the Horsepower of the bandsaw. My MM16 runs mush faster than the Crapsman highest speed. I think my blade speed is around 3600 or 3700 FPM - but it has a 4.8 HP motor. The smaller 12" saws with a 3/4 hp motor probably would stall if the pulleys were set up to run that speed.

Re: Band saw speed

#6

Re: Band saw speed

del schisler

>i have a delta 6" with rizer making it a 12" The Motor is 1 1/2 HP 3450 rpm with a 1 inch double belt drive pulley on the motor And a 6 inch double belt drive on the band saw All browing brand Cast iron pulley's I can resaw any wood any height and not have any trouble at all It may be wrong but works for me del

Re: Band saw speed

#7

William Falberg

Re: Band saw speed

William Falberg

>FWIW: My saws have always run at 4600 FPM with a 3/4HP motor, but now that I'm using 1HP motors I'm thinking of speeding it up some. It doesn't cost much to swap pulleys so why not try different speeds to see where your "sweet spot" lies. There's no hard and fast rules involved here that I know of, so decide for yourself what speed works best for you.