Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Adhesive for plastic (bottle)?

Posts

Adhesive for plastic (bottle)?

#1

Adhesive for plastic (bottle)?

North of the Border

>I need advice on what what glue to use to join two halves of a bottle together. (I cut out some plastic to make the bottle shorter.) The bottle is made of plastic material as shown in the pic here. The bottom has the number 2 inside a triangular arrows pattern HDPE. I read somewhere E6000 is the adhesive for plastic and wonder if epoxy may also be used. Any suggestions? Thanks.


img

Re: Adhesive for plastic (bottle)?

#2

Re: Adhesive for plastic (bottle)?

Dan Donaldson

>That is High density polyethylene and I don't think that there is any glue that will really stick to it. They usually weld seams.

Re: Adhesive for plastic (bottle)?

#3

Re: Adhesive for plastic (bottle)?

Kneale Brownson Dreaming of the Snow in N. MI

>Hot air welding or hot extrusion welder to apply an appropriate plastic rod to the seam. Something you could do with a plastic welder or maybe have a bodyshop do for you.

Re: Adhesive for plastic (bottle)?

#4

Amazing Goop Glue

Mark Goodall - ATL - tooljunkie

>From our experience with the Bottle Rocket competitions at the Science Olypiads, we found that Amazing Goop™ is the only glue that works (and about the only glue permitted) when gluing 2-liter pop bottles.

The glue remains slightly pliable after drying, but after 24 hours this stuff is almost impossible to remove from the plastic bottles.

Happy Woodworking!


img

Re: Adhesive for plastic (bottle)?

#5

JL

Re: Adhesive for plastic (bottle)?

JL

>Going to sound strange, but so be it.

I used to work for a manufacturer of flexible packaging. We often had to use adhesives to stick one film to another.

We either flame treated or corona (electric discharge) treated the film surface to promote the adhesion. When we did it on a lab scale, I used a propane torch or a small spark "zapper" to treat the surface.

After it was treated, I could use a 2 part polyurethane or a 2 part epoxy.

The heat welding also works quite well.

Re: Adhesive for plastic (bottle)?

#6

Re: Amazing Goop Glue

Dan Donaldson

>2 liter bottles are a different material. The one in the post is polyethylene and not much will stick to it. Except for the temperature resistance, it is similar to teflon.

Re: Adhesive for plastic (bottle)?

#7

Thanks all. I'll give Epoxy a try.

North of the Border

>

Re: Adhesive for plastic (bottle)?

#8

Re: Adhesive for plastic (bottle) - The result

North of the Border

>I tried the 5-minute epoxy and it worked. Thanks again to everyone who shed a light in this thread. When it comes to plastic adhesive, I think a little experiment is the way to go as we see in the discussion, there're so many different types of plastics that there's probably no one-suits-all glue out there.

Re: Adhesive for plastic (bottle)?

#9

Dale Lenz

Re: Would think...

Dale Lenz

>if you squeezed the bottle the brittle epoxy would break(?).

Re: Adhesive for plastic (bottle)?

#10

Re: Would think... - Good point

North of the Border

>It may. But since the bottle will not be subject to any sideway pressure, that's not a concern in my case (I'm making a wooden container (octagon shape) to put this bottle in).

Re: Adhesive for plastic (bottle)?

#11

Ahhh... okay

Mark Goodall - ATL - tooljunkie

>