Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

getting back on the horse

Posts

getting back on the horse

#1

getting back on the horse

Edward McCormack

>Hello everyone;

Well some of you might remember an earlier post of mine about cutting off my finger on a table saw in Feb. Well the "nub" is doing great, I'm in the prosses of getting a prosthetic finger. Just waiting for workmans comp. to come through with an OK.

I got back on the horse and am woodworking again(with a much greater respect for my tools). I was in the prosses of making a knock down craddle for a friend before i had my accident. The baby was born (a healthy lil' girl) so I needed to finish the cradle before she outgrew it.

To be honest with everyone i didnt know if i was ready but there was only one way to find out. So i turned on the table saw stood there for a min and let it run. The sound almost made me wet my pants well not quite but my heart was in my throat. I had to turn it off and walk away for a min. Looking at the wood i knew it wouldnt cut itself so i went back and did it. Ripping a piece of plywood from 15" down to 11 3/8" looked a whole lot smaller than it once did. AS SOON as i was done i grabbed a smoke and a beer and that was all the woodworking for the day. I have been back to the saw now 7-10 more times and each time its alittle less nerve wracking but the fear is still there, But im going to take that fear and use it to make me a smarter, safer, better woodworker. I'm not going to let it stop me from doing something i get pleasure from.

I would like to thank all of you here at woodcentral for your words of encouragement and well wishes. It helped to get back on that horse. I look forward to posting more weekend accomplishments. Thanks again.

Ed


img

Re: getting back on the horse

#3

Nice cradle!

Martin from Granbury

>Glad to hear you are back in the saddle. I bet you will be much safer in the future. I can only imagine what you went through to turn that saw back on.

Very nice cradle. Since I have a relative that will need one soon, can you give me a source for a plan?

Thanks, and welcome back.

Martin

Re: getting back on the horse

#4

Good for you Ed.

Thomas Skaggs, Foothills of Mount Level

>Ed,

I too had a bad table saw accident. I'll never forget the first day I used the saw after the accident. It was indeed a nervous moment for me. I can relate!

Looks like your first project back in the shop is a really nice one. I'm glad you are back on the horse!

Tom

Re: getting back on the horse

#6

Re: getting back on the horse

Ralph Turney

>I cut the ends off of two fingers (first knuckle) on a band saw 35 years ago, and when I went back to the machine shop after I recovered, my foreman had three band saw jobs waiting for me to do, first thing...scared the carp out of me, but I did get over it and you will too.

Good luck.

Ralph

Re: getting back on the horse

#7

JL

Re: Glad you got back on..

JL

>Pretty cradle.

Re: getting back on the horse

#8

Re: getting back on the horse

charlie belden

>Warranted fear will, in time, turn to a healthy respect and the taking of reasonable precautions - all good things.

And there's nothing like an infant to motivate one. Clearly the results of that motivation will benefit this little girl - and perhaps her child or two.

Nicely done sir, all the way round.

charlie belden

Re: getting back on the horse

#9

Re: getting back on the horse

Barry Irby

>Congratulations on getting back into the shop. I have been there. Well, not as bad, I cut the tip off the thumb on my right hand when I was about 16. I still have the Radial Arm Saw. And the blade. 43 years later.

As they say, let this be a lesson to you. Don't get careless. Remember. And, drink the beer after you stop for the day.

And thank you for sharing with us. Maybe it will help some of us remember that tools are dangerous and we all need to treat them with respect.

Good looking cradle. Nice job.

Re: getting back on the horse

#10

A future heirloom

Dan Mitchell

>Only real "tool related" injury I've had was cutting the tip of my thumb in shop class 30-some years ago. Took however many stitches an injury of about 3/4" would require, but not too traumatic. In fact, I milked the injury for all it was worth, getting out of gym class for several weeks!Still have a scar but didn't lose any part of the member.

If the same thing happened today, especially at the level of your experience, I don't know if I'd be able to go back to the activity. Excellent work overcoming your fears & a beautiful cradle to boot!

Dan

Re: getting back on the horse

#11

Re: A future heirloom

Dan Mitchell

>I should add my injury was on the much-less intimidating band saw.

Then again, maybe that's why I've yet to add one to my shop! ;-/

Re: getting back on the horse

#12

Re: getting back on the horse

Brian Gray in Sandusky, OH

>Congratulations.

I put a chisel into my finger about 5 years ago and severed two tendons. (four days before my wedding...made for interesting wedding photos.)

I searched through the messageboards, but apparently WC doesn't archive back that far. I started a good thread about safety...pictures and all!

It takes a bit of courage to start a thread about your mishap here...it's kind of like admitting that you are an idiot!!! (or that you had an idiot moment)

But that's not the case. It can be a dangerous hobby. Safety first, and if a reminder is a couple severed tendons, or a stubby finger, then take what life gives you...but don't let that keep you from enjoying woodworking. Allow it heighten your sense of safety.

If it makes you feel any better, Garret Hack is missing the tip of his middle finger, and once while I was at Ernie Conover's place, he nicked his thumb on the bandsaw...So even the gurus have had their moments.

Keep up the good work.

Re: getting back on the horse

#13

Way to go, Ed! Keep on keepin' on!

Stuart Hough

>

Re: getting back on the horse

#14

Re: getting back on the horse

Larry Clinton At Frankfort (Central)., Indiana

>Nice looking cradle, should pass through many generations. Don't know if you have looked at them, but I won't use my Unisaw without my set of Grr-Rippers. I have had to rebuild mine due to cutting a few slots in them, but the $35 or so was a whole lot less painful than sewing up or losing a finger. I use them on my router table and band saw once in a while too (depending on the project), as they give me a lot more control than other push blocks on all the machines. No affiliation with the company - but I sure recommend them.

Re: getting back on the horse

#15

Re: getting back on the horse

Joe in a Cleveland suburb

>Nice job Ed.

I give you lots of credit. If I had an accident like yours I'm not so sure I could go back to using the saw.

I've not had an accident (one close call though) and my cabinet saw scares the heck out of me every time I turn the beast on.

Joe

Re: getting back on the horse

#16

Thanks!

Martin from Granbury

>

Re: getting back on the horse

#17

Re: getting back on the horse

Stan Fettig

>My "accident" happened at the router table with a pannel raising bit. It mangled 2 finger tips on my left hand. There was enough shreds of skin and muscle for the doctor to stitch things closed but the bones were in too many pieces for quick healing. That was back in May. Although I've been back to the table saw and hand held power tools I have not yet stepped up to the router table but am ready to get back on that horse and finish our cabinet doors. The horse seems much bigger than he used to be though. The lesson I learned was, "when you get tired, STOP." Never again will I think that I'll do just one more.

Re: getting back on the horse

#18

Re: Good for you Ed.

George@Colonel's Workshop-Havertown PA

>Good Afternoon Ed,

Could it have been worse? I've been very lucky because there has been almost no damage done to me when I've been too tired. It must have been very difficult to overcome that trauma, and you can be forgiven for avoiding the router table for awhile. Your cradle is lovely.

George

Re: getting back on the horse

#19

Re: Good for you Ed.

Bart Leetch

>I got hurt on one of those small aluminum router tables 2 of which I got almost free. I lost control because of the smallness of the table top & both tables wen free flying right into a dumpster after I made them so no one could ever use them again.

One caution if you respect a tool before or even after you get hurt thats good if your afraid of the tool before or after getting hurt stay away from the tool

Re: getting back on the horse

#20

Re: getting back on the horse

Joe Tomei

>Soon after setting up my new table saw, I made a push stick for obvious safety reasons. I followed the sketch in the manual using a fine piece of oak, sharp corners and all. After a few weeks, I accidently brushed the blade with the push stick. It promptly (surprisingly fast) rammed into my wrist. A lot of blood followed. But I got it taken care of.

NOW MY PUSH STICKS ARE MADE OF BALSA WOOD. WHEN THEY NICK THE BLADE THEY JUST TURN TO DUST WITH NO DAMAGE. nEW STICKS ARE CHEAP.

Re: getting back on the horse

#21

Re: getting back on the horse

Fred Davis

>Ed,

That's a very nice crib/cradle you made , I am sorry it cost you a finger in the process.

Replace the word fear with the word caution and remember machines only cut what is fed into them and you will do fine.

After reading the thread on what guys have done to their hands ,it almost made me want to go out to the shop and hurt myself so I could identify. ;-))

After fifty plus years of working with saws , about the only thing my hands got out of it was Arthritis.

FredD

Re: getting back on the horse

#22

Re: getting back on the horse

Rob Stokes in North Vancouver

>Ed - I took the tip of my finger off on the table saw a couple of years ago and in a funny way, I'm kinda glad it happened. Like you I was a little nervous about "getting back on the horse", but I actually had to continue working that same evening to finish a project.

Since then, and every time I use the table saw I experience, well, it's not fear, but it's a sharp moment of respect. I've slowed down near it now, not a lot, but enough to to a quick mental double check of how I'm doing things, and I'm pleased to report that I've given myself hell a few times and changed process' to remove shortcuts or make a cut more safe.

I refuse to fear the saw - that's just dumb. But I'm glad for the opportunity to be able to give the saw the respect it's due, and the respect I never used to give it.

As for the finger, well - I've had to re-learn how to button my shirts, and typing took a while to re-figure out, but not a big deal. I can't tell when it's going to rain, but I think I may have a reasonable snow warning system now... And besides- I've got ten fingers. If I take them all to the grave, I wasn't trying hard enough in life :)

Rob