Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

LEIGH FMT mortising jig question

Posts

LEIGH FMT mortising jig question

#1

LEIGH FMT mortising jig question

charlie belden

>(I'm posting this question to several woodworking forums in hopes of getting

an answer. So if you've seen it before, apologies)

I'm studying the LEIGH FMT mortising jig and the question of registering

the part that will be end grain mortised to the plane of the jig's table has

come up.

It appears to me that the only way to register the part to the jig's table

is against the little pull out "cross hairs thing". THAT is not very much

surface to register against - and that registration is really important.

If the part ends up just a little high or just a little low - or tilted left or

right - just a little bit - it can result in a bad fitting joint.

It looks like the jig table can be moved foreward and back - but the range

of motion appears limited - and it's not clear if the jig table can be slid

foreward enough to let you register the end of the part to be mortised

against it. So if you've got the LEIGH FMT jig - CAN you slide the jig's

table foreward enough to use it to register the end grain mortised part

against?

If it can't, is this actually a significant roblem - and how do YOU solve it?

charlie b

Re: LEIGH FMT mortising jig question

#2

Did you try their Tech Support?

North of the Border

>Technical Support

Email help@leighjigs.com

or toll-free at 1-800-663-8932.

Re: LEIGH FMT mortising jig question

#3

Re: LEIGH FMT mortising jig question

Jesse Cloud

>Good idea to try Leigh's tech support - they are top notch.

But here's a stab at it. The workpiece should be posited against the vertical fence which attaches to the side of the FMT. If you take care to ensure that the fence is square to the table, then the workpiece should be at least parallel to the table surface. The piece registers against the crosshair for height. The crosshair isn't very wide, but it should give you good enough registration for height, just be sure not to push beyond the first contact and double check for snugness after you have the workpiece clamped.

The height dimension shouldn't be critical anyhow if you leave room in the bottom of the mortise for glue - I usually leave about 1/16th.

Hope this helps.

Re: LEIGH FMT mortising jig question

#4

Re: LEIGH FMT mortising jig question

Clay Foster

>Charlie,

I've had one for several years, and have been real happy with it. It's remarkably accurate. You can cut 100 mortise and tenons, and they will all be identical and interchangeable.

There is a fence that you use to align the stock for vertical accuracy. The cross hairs thing is just that, for getting the part lined up. Maybe this picture will help. When you cut the tenon, it is actually moved out of the way.

The table slides both forward and back and right and left. The maximum travel is about 21/2 inches. I think you could move it to cut to the center of a board 5" thick. When you lock it down, it stays locked. There's no give or slop.

When I want accuracy within .001 I use my Leigh jig. If I have really big stuff, I use my Rojek horizontal mortiser.


img

Re: LEIGH FMT mortising jig question

#5

Re: LEIGH FMT a better fence *LINK*

Peter Gregory

>I have one and it isn't a problem, the thing just works. They have a new and better fence, that comes with a new machine, that helps get the 90 degree right. I blew the $15 on the upgrade and I'm happy I did.

I sometimes wonder if I should have gotten a Wood Rat instead, but I'm very happy with the FMT. Just completing a A&C bunk bed, with 10 slats on each of 4 head/foot boards, with a M&T at each end - or 80 M&T's. Knocked them out and each one fits in any position. If you setup right, there is no tuning.


Better fence, upgrade

Re: LEIGH FMT mortising jig question

#6

Re: LEIGH FMT mortising jig question

charlie belden

>First, let me thank you for your repsonses, the links - and the suggestion to call LEIGH's tech support. I did, left a message - on Sunday - and this morning (Tuesday) Barry of LEIGH tech support call me back - and apologies for not being able to get back to me on Monday. Apparently it's the weekend warriors (read woodworker who busts his or her butt off making a living and supporting a family all week long) encountering a problem or having a question about their new jig.

Now I don't recall ever having a tech support person calling back a day late EVER apologizing - hell, often they don't call back at all. Thought I was dealing with Lee Valley ; ).

Anyway, Barry knows the FMT and that became very clear over the next half hour of me asking questions and him providing the answers- and pointing out answers to questions I'd probably have sooner or later.

Between the downloadable pdf chapters of the FMT manual off the LEIGH site and what I learned from Barry, I have a pretty good understanding of what and how the FMT can do what it does.

The new vertical fence can be self squaring to the jig's table top - correcting a problem with the original fence - mounted "right side up" or "upside down". And when mounted "upside down" it also provides a clamping surface when mortising end grain of narrow parts. And, thanks to talking with Barry, it also provide support for thin parts mounted horizontally.

The LEIGH FMT is a very versatile jig - with GREAT tech support.

Thanks again for the help.

charlie belden