Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Wet to dry, how much length loss?

Posts

Wet to dry, how much length loss?

#1

Wet to dry, how much length loss?

Peter Gregory

>I'm building a structural project with Doug Fir (4X6 and 2X6's). The 2X6's are very wet and the 4X6's are fairly dry (no meter, so no exact %, sorry). It is fine if they expand and contract in the width, I can deal with that. I'm wondering how much length I'm going to lose, as they dry. I found the calculators, but they address width only.

Anyone have a guess of how much of my 9' length I'm going to lose over the next couple of years?

TIA

Re: Wet to dry, how much length loss?

#2

Lee Grindinger

A couple links for you

Lee Grindinger

>This one discusses maple...,

http://www.woodweb.com/knowledge_base/Calculating_longitudinal_shrinkage.html

This one is much more thorough and species specific. I believe the info you want is in Chapter1.

http://www.fpl.fs.fed.us/documnts/usda/ah188/ah188.htm

Lee

Re: Wet to dry, how much length loss?

#3

Lee Grindinger

Page 12 of the second link

Lee Grindinger

>Sadly, there is no definitive answer especially since you don't know how wet or dry your wood is or will become. .2% (two tenths of one percent) is normal.

.216" or less than a quarter of an inch over nine feet if your wood is very wet and typical wood not containing a lot of different grains.

Lee

Re: Wet to dry, how much length loss?

#4

Re:Sounds like an amount to plan for

Peter Gregory

>I will make things to allow a quarter inch of movement and that should be close enough.

Thank you.

Re: Wet to dry, how much length loss?

#5

Re: Wet to dry, how much length loss?

Sgian Dubh

>Typical shrinkage in most species, as Lee mentioned, is very small in normal wood. It's typically about 0.1% for most species from green (30% MC) to 8% MC. Therefore a 3000 mm (~120") long plank will shrink in length by 3 mm (1/8") from green to 8% MC, and probably just half this amount if the wood dries from only 20% MC to 8% MC.

Reaction wood and immature wood can move as much as 20 time more, that is by up to 2%, ie, the same 3000 mm long piece above, if it is full of either reaction or immature wood, could shrink by as much as 60 mm from green to 8% MC. Both these types of faulty wood are almost never used in wooden structures due to their instability and tendency to warp and cause other problems. Slainte.

Re: Wet to dry, how much length loss?

#6

Re: Wet to dry, how much length loss?

Peter Gregory

>Thank you. Sounds like if I can deal with a little reduction in height, I'm golden. Have to post a picture when I'm done. This is either the stupidest idea I have had in a while or brilliant. Maybe both?

Re: Wet to dry, how much length loss?

#7

Re: Wet to dry, how much length loss?

Barry Irby

>Lee and Sgian are right.

This is an important issue for the truss industry. If the wood changes dimension in length once fabricated into trusses, the trusses change shape. There is a phenomenon known as truss lift or truss uplift. Generally in winter the trusses arch their backs and lift the ceiling in the middle of the house as much as and inch or two. If they do it once within a few months of installation, it indicates the trusses were fabricated from green wood. If they cycle summer to winter, they were fabricated from reaction wood or wood cut from juvenile trees. Juvenile wood is the curse of the truss industry. Also has to do with how much insulation is in the ceiling. So unless your lumber was cut from small trees, you should be good to go with a 1/4".