Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Bending an 8 foot 2x6 for a treehouse

Posts

Bending an 8 foot 2x6 for a treehouse

#1

Bending an 8 foot 2x6 for a treehouse

Stephen Roth

>I am making a treehouse for my son in the shape of a boat. For the bottom 2 joists, I need to bend 8 foot 2x6's on a curve from a point 3 feet wide at one end, down to a point on the other. It is a relatively gradual bend, that I could probably just force the wood into taking. However, I was also thinking of soaking the wood in water overnight to avoid cracking or splitting, and then just letting it dry once I nail it up. Would that be better?

I know I could just steam bend it, but I didn't want to take the time to set up for steam bending.

Re: Bending an 8 foot 2x6 for a treehouse

#2

Re: Bending an 8 foot 2x6 for a treehouse

Lee Schierer - McKean, PA

>Most treated lumber is already pretty wet. I would think that if you make some boards that would serve as cross pieces to the lengths needed that you could bow the boards with the help of some pipe clamps. Bolt the ends together with a couple of sturdy hinges and through bolts not wood screws. Place cross pieces at appropriate places along the length and fold the two long pieces back along each other. Try to get pieces that are free from knots as they wold be less likely to break.

Another way would be to use two 1 x 6's laminated together with water proof glue. They should bend relatively easily.

Lee

Re: Bending an 8 foot 2x6 for a treehouse

#3

Re: Soak

Mark Mandell - Gone Round In Jersey

>For more than overnight, and add some liquid dish detergent to the soak water as it will assist penetration. You still won't get very deep into the wood without pressure, but it will help the surface fibers.

You might also do better with a longer board. Spreading the tension over a 12 footer will be easier, and, when done, you can then cut off the excess but use the 4' sections elsewhere.

mm

Re: Bending an 8 foot 2x6 for a treehouse

#4

JL

Re: Bending an 8 foot 2x6 for a treehouse

JL

>From your description, you are bending two 8' 2 x 6" pieces and your curve should go from 3' to a point?

If you use "wet" lumber as opposed to bone dry, you could probably make it work. Soaking the lumber in water won't do much though if it is kiln dried. Like Lee suggested, you might try bending the 1 x 6" and doing a glue lamination. If it is kiln dried, usually steam bending does not work (DAMHIKT).

Re: Bending an 8 foot 2x6 for a treehouse

#5

Re: Bending an 8 foot 2x6 for a treehouse

howard

>Steve,

Maybe I am not reading this correctly, but bending a 2 x 6 seems tricky, and if you want to soak it then I'd think you'd get a fair amount of stress and cracking as it dried. A marine grade ply laminated together would give you a solid curve. There are also pressure treated ply's available, but there is the issue of your kids putting their hands on it. But, I think doing the bend as a lamination would work better.

Re: Bending an 8 foot 2x6 for a treehouse

#6

Just come by my local building supply

Henry Higginbotham

>They've got 2x6s in any shape you could possibly want (other than straight, of course).

Re: Bending an 8 foot 2x6 for a treehouse

#7

Re: Just come by my local building supply

Tom Dunlap

>That is SOOOO funny! Thanks for the out-loud laugh :)

Tom

Re: Bending an 8 foot 2x6 for a treehouse

#8

Heehee

Lee Schierer - McKean, PA

>I was going to suggest going to one of the Borgs and leaving the lumber lay in the sun for about an hour....

Lee

Re: Bending an 8 foot 2x6 for a treehouse

#9

Thanks.

Stephen Roth (In New Jersey)

>Thanks for all the comments (and humor). I think I will go with laminating. I hope the Titebond III glue holds till I have grandchildren.

Re: Bending an 8 foot 2x6 for a treehouse

#10

Re: Bending an 8 foot 2x6 for a treehouse

Pete in Holland, MI

>Might be better to use a couple 1x6's and glue/screw them together. Bent a 12' 2x6 one time about 18" from straight. Took a suprising amount of force to do that. No knots and straight grain are a must, along with beign sopping wet (tie up to a dock or lay in a stream for several days, then immediately get to bending it once you remove it from the water.

Carefull ! ! ! Wound up springs can be dangerous ! ! !

Re: Bending an 8 foot 2x6 for a treehouse

#11

Another Vote For Lamination (NM)

George (Oxford, NC)

>

Re: Bending an 8 foot 2x6 for a treehouse

#12

on soaking

Bill Tindall, E.TN

>It has been my experience that once dry the wood is "set" and simply rewetting it, even for days, has no effect on its bendability. If you live in the land of yellow pine salt treated lumber it is often soggy wet from treatment and bends like wet noodles. Or, if there is a saw mill handy get them to cut you a piece of something, and fresh cut, it will be very limber.

Re: Bending an 8 foot 2x6 for a treehouse

#13

Re: Bending an 8 foot 2x6 for a treehouse

Barry Irby

>I bent some treated 2x4's to laminate them for some garden bridges I was building. The pieces were twelve feet long and the form had less than a foot of bend. IE, the arches were about ten inches tall in the center. I put one piece on place and it worked fine. The second one broke and about hurt me. After that, I kerfed every one of them about half way through, with the kerfs on the bottom side and about four inches apart. I usually kerfed right through knots and on both sides of knots.

So, what I am saying is, either use thinner stock and several layers, or kerf the pieces (which has the effect of reducing them to thinner pieces). Or go find some at the local Borg that are already warped to your satisfaction.

I used 3M 5200 glue which took a week to set. It's been ten years and the bridges are still there.