Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

trunk bottom question

Posts

trunk bottom question

#1

trunk bottom question

Bill Tindall, E.TN

>How are trunk bottoms installed. Like a drawer bottom in a dado, but what about expansion. Leave it open on the back like a drawer?

I have a vision of a coopered curved top, rift oak. Toy chest. Any ideas for a secret compartment for a trunk? Any trunk ideas in general. Never made a trunk before or examined one closely.

Re: trunk bottom question

#2

Re: trunk bottom question

John McGaw

>I have made quite a few blanket boxes and chests although no toy chests. The most satisfactory bottom method I've found is a wide (3/8"-1/2") tongue and groove with 1/2" shiplap coming in a close second. I leave enough gap in fitting the bottom boards to allow for the expected movement. If I'm feeling fancy I might rabbet the ends of each board and the outer edges as appropriate so that they can fit down into the mounting cleats or dado a bit giving a little more volume in the chest without sacrificing much strength.

Using a dado around the chest bottom works fine but makes repairs impossible. I finally settled on a cleat all around the bottom edge, maybe 1/2" X 1/2" This is screwed in place flush with the bottom edge of the sides so that it can be removed. The bottom boards are then laid in place. I use a very thin piece of weatherstrip in the grooves both to seal against dust and bugs as well as to help center the boards. Boards are laid in place and both end strips are fastened lightly to the cleats using a couple of brads. I then fit 1/2" quarter-round with mitered ends to hold the bottom strips down against the cleats. This trim is glued and bradded in place since it will be permanent, any repairs being made by removing the bottom cleats.

I have used similar construction for drawers that will be expected to hold a lot of weight and it works well there too, allowing me to dovetail all of the corners of the drawer for strength and supporting the bottom all around.

Just my $0.02...

Re: trunk bottom question

#3

Re: trunk bottom question

Howard Acheson

>What are you going to make the trunk out of? Solid wood or plywood? If plywood, use a plywood bottom and you have no problems. If the trunk will be made from solid wood and the grain on the front, back and sides all runs in the horizontal direction, you can again use plywood and glue it in.

If however, you want to use a solid wood bottom, then use the technique that John suggested. Or, use some other technique but allow enough depth in the bottom groove for the bottom to expand and contract. Don't glue it in.

Personally, unless you are trying to make a strict period copy, I would recommend a plywood bottom.

Re: trunk bottom question

#4

Re: trunk bottom question

Glenn Madsen, SF Bay Area

>If this IS a toy chest, I want to add this:

I have grandchildren. How they play with and in their toy chest is not gentle. When I build them theirs (what they now use is Rubbermaid), it will be industrial strength. Maybe with 1.125" subfloor as a bottom layer, blocked up with framing timbers.

Seeing three of them jumping in it happens frequently.

Re: trunk bottom question

#5

Hidden compartment

Neal in San Jose

>I've put hidden compartments into chests by adding a tall (3 or 4 inch) base molding around the bottom of the chest and making the front piece of molding the front of a drawer. Picture a chest on chest arrangement. The bottom of the chest obviously has to be raised to allow room for the drawer, and the ends of the front piece of molding must be carefully done so that when the drawer is closed, it isn't too visable. I've used mitered corners, but they tend to get a little ragged over time, and it and loses the effect, so I now extend the drawer front so it looks like the sides butt into the back of the drawer front. Relieve the bottom of the drawer front with a cut out so it looks like the chest is sitting on legs so you can get fingers under it.

You can also just add a false bottom sitting on cleats above the "real" bottom. Two problems with this are that the chest must be empty before you can get to the false bottom, and there needs to be a finger hole which can be obvious, or some other way to get the bottom out (think magnets!). Fine WoodWorking had an article on hidden compartments that had several clever ideas within the last 10 years or so, but I'm at work and can't go looking for the issue.

I was making a HUGE amoire when the FWW article came out. The article inspired me to put 6 hidden compartments into the amoire, and I probably lost money on the commission, but it was fun challenging the owner to find all of the compartments. She found 3 and I had to tell her about the other 3. I'm not sure she ever did tell her husband about them!

Re: trunk bottom question

#7

secret compartments *LINK*

GolfSteve in Calgary

>I saw a great big chest in a store once that was full of secret compartments. I made a bunch of sketches for my own reference and posted them here a while back.

Someday I'm going to make one of these:


Secret Compartments in a Chest

Re: trunk bottom question

#8

Re: trunk bottom question

Dan Cekarmis

>I built a toy chest for my granddaugthers and for safety reasons I used 1/4" pegboard. Kids love to crawl into things and I wanted plenty of air in case they closed the lid. I used a dado in the bottom of the four sides and then used two 3/4" thick pieces of maple (the toy chest was made of cherry and maple) to support the bottom. The maple had a lap joint into the front and back panels. The 1/4" pegboard sits in the dado and on top of the 3/4" maple supports.