Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Trowel-on filler under veneer?

Posts

Trowel-on filler under veneer?

#1

Trowel-on filler under veneer?

pecker

>Ordinarily I veneer flat panels in a vacuum press, then saw up the panels into the required parts for a project. This time I needed to build the assembly first and try to veneer it afterward. Unfortunately due to a slight misalignment and some cupping of a piece of plywood, I have a broad area, about 6" x 36" that is not flat with it's adjacent panels.

So...I need to be able to apply a filler, about 1/32" thick to this area and sand it smooth before putting it in the press. Drywall compound would work great for this, but I don't know if the Titebond cold press veneer glue will adhere to it. Can anybody recommend the appropriate product to use for this filled in area, for this application?

Thanks.

Re: Trowel-on filler under veneer?

#2

Re: Trowel-on filler under veneer?

Ed Mulligan, Cape Cod

>Try auto-body filler, e.g. 'Bondo'.

Ed

Re: Trowel-on filler under veneer?

#3

Re: Trowel-on filler under veneer?

Mark Mandell - Gone Round In Jersey

>Joint compound will, over time, fracture and powder in this application. I'd suggest a filled resin. Auto body filler comes to mind, but it can have adhesion issues on wood over time. I suggest that you make your own out of polyester resin (auto supply stuff) with adding powered filler. This will wet the wood fibers better. You could also, I suppose, take some "bondo" which is polyester as well and add some pure resin to it. You'd have to test how much hardener to use on the new mix.

Apply to the area and the use a metal straight edge longer that the width of the depression to "screed" off the excess.

Of course, it might just be faster to rip that section out and replace it with flat stock. |;-}}

Re: Trowel-on filler under veneer?

#4

Re: Trowel-on filler under veneer?

pecker

>My main concern is if the Titebond veneer glue, which is a PVA type product, would stick to something like bondo or resin over a wide area like this. (and I can't saw it apart at this stage)

Re: Trowel-on filler under veneer?

#5

Re: filler under veneer?

Mark Mandell - Gone Round In Jersey

>PVA will stick to itself, so

Take your liquid TB, add some inert filler the same way you would with the resin to get a pasty consistency, and spread that with the metal screed. Let dry and check for highs and lows, fill or sand to level. I'd rough the surface with a bit of 80 grit to help the stick, but vacuum off well to remove any bump-producing granules.

Re: Trowel-on filler under veneer?

#6

Re: filler under veneer?

pecker

>"PVA will stick to itself,"

Are you sure about that? On any yellow glue joint that I've tried to repair, the old dried glue needed to be removed first in order to make a sturdy connection.

Re: Trowel-on filler under veneer?

#7

PVA

Mark Mandell - Gone Round In Jersey

>Over a wide area with the surface roughed to provide an 80-grit "tooth", I think you should be in good shape. Use a porous filler like wood flour or even 2x pumice rubbing compound to give it additional stickability [tech term].

You have another option and that is to apply veneer just to the low area, then sand it off level with the adjoining surfaces. Easily doable if you have access to a good drum sander of sufficient size.

mm